Categories
Design

How to position your netgear arlo cameras the easy way

Setting up your Arlo essential camera is a pretty straightforward process.

The steps below will help you right from powering on the camera up to its final synchronization.

Recommended steps regarding How to Set up Arlo Essential Camera

Step 1. Getting started

Unbox the Arlo Essential camera package and read through all the instructions mentioned in the user manual.

This will help you in getting accustomed to all of its basic features and controls. Moreover, download and install the Arlo app on your Smartphone.

Once downloaded, set up your account on your app, and it will then prompt you with further steps to add the device.

The Arlo essential camera needs to be charged first. To start ahead with the task, open the micro USB charging port cover on the camera.

Afterward, connect the provided micro USB cable to the camera. Doing that, you must also connect the other end to a USB charging source or an AC power adaptor.

The battery will get automatically charged from here on. Wait for the blue LED light as that confirms the full charge to the Arlo essential camera.

Step 2. Syncing the device

Your device comes in a ‘Shut down mode’ to reduce the battery charge before its installation.

Wake the camera by pressing the SYNC button placed at the bottom of the device. Once you press it for 1-2 seconds, the camera will wake up with a LED light flashing blue.

Add the device to the Arlo app by following the provided instructions. Please ensure to recharge the battery before starting ahead with the process or the device will not respond. The LED light on the camera signifies its charging, syncing with wifi and firmware update.

  • Slow blinking blue: The camera is about to get paired with a WiFi network.
  • Fast blinking blue: The camera is successfully paired with a WiFi network.
  • Blinking amber: The camera is out of range with a WIFI network, a connection error occurred during the pairing process, or the battery charge percentage is too low (15% or less).
  • Alternating blue and amber: The device is undergoing a firmware update.

The camera can then be connected to the Home WIFI network by simply following the Arlo app’s instructions. Refer to the LED light status details mentioned above to check and confirm a secured and successful connection.

Step 3. Mounting the camera to the desired location

You now need to decide upon the desired location for its placement. Check for a spot that offers the complete field of view according to your needs and preferences.

Moreover, do ensure that the location is supported by strong wifi coverage with your home network.

You can check for the Wi-Fi connectivity and related aspects right on the Arlo app. Afterward, proceed ahead with the mounting of the Arlo essential camera by following the provided steps.

  • Position the mount and tighten it with the provided screws in the package. Use drywall anchors when and wherever required.
  • Carefully attach the camera to the mount by positioning the camera to the two mounting holes (rear and bottom part)
  • Swivel and tilt the device according to your security requirements.
  • Your Arlo essential camera is successfully setup

Step 4. Testing the camera

It is always recommended to check and test all the features and controls of the camera beforehand. To proceed, tap on the Arlo app and go to Settings >My devices > Select camera>Device utilities> Motion detection test.

Once done, make random movements around the camera. Check whether the LED light on the device is blinking amber. You can now shift the slider on the app to make changes in the motion sensitivity levels.

This comes as a default setting in the camera. Hence, you have to change it according to your needs and preferences after the motion detection test.

Additionally, change the camera’s angle and position to secure the desired results with its motion detection and other features.

The camera positioning feature can opt if the device is not recording, streaming, or detecting any motion. During Camera positioning, the device streams the video as fast as possible without any buffering issues.

The changes can be made while using the Arlo app on your smart device by following the below steps:

Settings >My Devices>Device utilities> Camera positioning

The device can be armed or disarmed for the motion detection features accordingly.

Bottomline for How to set up Arlo essential camera

The process regarding How to set up Arlo essential camera is quite straightforward. Just get yourself accustomed to all of its basic controls and features.

If you face any issues during the connection process, refer to the user manual or call the Arlo customer support team.

Padėdami daugumą apsauginių fotoaparatų, trunka šiek tiek laiko ir truputį bandymų ir klaidų, kad galėtumėte juos puikiai nustatyti. Tačiau “Netgear” pridėjo keletą funkcijų, dėl kurių “Arlo” fotoaparatams nustatomas procesas yra daug lengvesnis.

SUSIJĘS: Kaip nustatyti “Netgear” “Arlo Pro” fotoaparato sistemą

Ne per sunku pasiekti idealų kampą apsaugos kameros; turėtumėte sugalvoti spąstus ir pažiūrėkite į tiesioginį vaizdo įrašą, kad pamatytumėte, kiek gerai dirbote. Jei jums buvo šiek tiek, atliktumėte tam tikrus koregavimus.

Tačiau judesio jautrumo koregavimas tikriausiai yra labiausiai kruopštus procesas, nes gali būti keli bandymai jį pasiekti netgi nuotoliniu būdu, jei to norėsite. Naudodamiesi “Netgear” “Arlo” fotoaparatais, programoje yra funkcijų, dėl kurių įdiegimo ir padėties nustatymo kameros yra daug lengviau.

Pirma, rasite idealią vietą fotoaparato montavimui

Prieš pradėdami neria į “Arlo” pozicionavimo funkcijas programa, fotoaparatas turi būti kažkur įdiegtas (žinoma).

Tik jūs galite turėti geriausią sprendimą, kai norėsite rasti geriausią vietą savo “Arlo” kamerai, nes kiekvienas namas yra kitoks. Tačiau “Netgear” siūlo keletą savų pasiūlymų, tokių kaip didelis fotoaparato pateikimas ir švelnumas.

Taip pat galite jį nustatyti tiesiai ant lentynos, nes fotoaparatas turi plokščią dugną. Tiesiog įsitikinkite, kad lentyna nėra per didelė, nes jūs gausite daugiau rėmelio lubų, o ne svarbius bitus.

Naudokite programos “Padėties režimą”

“Arlo” turi funkciją vien tik fotoaparato pozicionavimui, kad būtų užtikrintas geriausias matomasis kampas be trinties. Padėties režimas, kaip jis vadinamas, sąmoningai sumažina vaizdo įrašo kanalo kokybę, kad sumažintų vėlavimo trukmę, taigi, kai perkeliate kamerą į padėtį, programoje pamatysite beveik realaus laiko vaizdą.

Norėdami atidaryti šią funkciją, atidarykite “Arlo” programą savo telefone ir bakstelėkite skirtuką “Nustatymai” apatiniame dešiniajame kampe.

Bakstelėkite “Mano įrenginiai”.

Pasirinkite fotoaparatą, į kurį norite nukreipti.

Slinkite žemyn ir bakstelėkite “Padėties režimas”.

Gausite fotoaparato vaizdo įrašų kanalą realiuoju laiku ir nieko kito.

Iš ten įdėkite fotoaparatą, kaip norite. Jūs vis tiek turėsite šiek tiek atsilikimo, bet tai bus tik maždaug 1-2 sekundės.

Koreguokite fotoaparato judesio jautrumą

Panašiai kaip ir pozicijos režimu, programoje taip pat yra funkcija, vadinama “judesio aptikimo testu” , todėl lengviau koreguoti judesio jautrumą be daugybės bandymų ir klaidų, dėl kurių paprastai reikia pastebėti kelias dienas.

Norėdami pasiekti šią funkciją, grįžkite į tą patį ekraną, kuriame pasirinkote pozicijos režimą, tik vietoj to, kad pasirinktumėte tai, palieskite po jo “Motion Detection Test”.

Iš ten pamatysite slankiklį, kuris leis jums koreguoti fotoaparato judesio jautrumą.

Prieš fotografuojant bus rodomas nedidelis mėlynas šviesos diodas kai jis aptinka judesį tam tikru jautrumo nustatymu. Taigi viskas, ko jums reikia padaryti, yra vaikščioti prieš fotoaparatą, stebėkite, kad mėlynas indikatorius įsižiebtų, ir atitinkamai sureguliuokite jautrumą.

Lizdas gali atsijungti, kol esate darbe, todėl jūsų šildymas ar aušinimas būna tik tada, kai esate namie. Jei nepavyks, kai grįšite namo teisingai, nors jūs galite laukti valandų nepatogioje būstinėje. Jei turite “Automatic Pro”, jūsų automobilis gali pasakyti “Nest”, kad jis pradėtų pašildyti, kai tik išeinate iš darbo.

Dėl “Alexa” ir jo atviros API galią jūs galite kontroliuoti daugybę įrenginių, naudojančių tik jūsų balsas. Jei turite “Eero” “Wi-Fi” sistemą, netgi galite valdyti savo namų tinklą “Amazon Echo”. Neseniai atnaujinus ir “Eero”, ir “Eero” programą, įmonė “Alexa” palaikė, taigi, jei turite “Amazon Echo”, “Fire TV” ar naujesnės “Fire” tabletės, galite naudoti “Alexa”, kad suteiktumėte nedideles balso komandas į savo “Wi-Fi” tinklą.

Při umístění většiny bezpečnostních kamer trvá nějaký čas a trochu pokusů a omylů, aby byly dokonale nastaveny. Netgear však přidal některé funkce, které usnadňují instalaci pro své kamery Arlo

SOUVISEJÍCÍ: Jak nastavit kamerový systém Netgear Arlo Pro

Není to příliš obtížné získat perfektní úhel bezpečnostní kamery; musíte se uhodnout a pak se podíváte na zdroj živých videí, abyste viděli, jak dobře jste vykonali práci. Kdybyste byli trochu zbytečně, udělali byste nějaké úpravy.

Přizpůsobení citlivosti pohybu je však pravděpodobně nejdůležitější proces, protože to může trvat několik pokusů o to, aby se to dostalo i vzdáleně tam, kde to chcete. S kamerami společnosti Netgear Arlo jsou však funkce, které usnadňují instalaci a umísťování kamer.

Nejdřív najděte ideální místo pro montáž fotoaparátu

Než se ponoříme hlouběji do funkcí pro určování polohy v Arlo (samozřejmě).

Pouze vy můžete mít nejlepší úsudek, pokud jde o nalezení nejlepšího místa, kam umístit kameru Arlo, protože každý dům je jiný. Nicméně, Netgear nabízí několik vlastních návrhů, jako je umístění fotoaparátu na výšku a trochu se na ní.

Také můžete nastavit na police, protože má ploché dno. Jen se ujistěte, že poloha není příliš vysoká, protože skončíte spíše se spoustou stropu v rámu než důležitými bity.

Použijte “Režim polohy” aplikace

Arlo má funkci výhradně pro umístění fotoaparátu pro dosažení nejlepšího možného úhlu pohledu bez jakéhokoliv tření. Režim pozice, jak se tomu říká, záměrně snižuje kvalitu posuvu videa, aby se zkrátila doba zpoždění, takže když přemístíte fotoaparát do polohy, uvidíte v aplikaci přibližně v reálném čase zobrazení

Chcete-li otevřít tuto funkci, otevřete aplikaci Arlo v telefonu a klepněte na kartu “Nastavení” v pravém dolním rohu.

Klepněte na “Moje zařízení”

Vyberte fotoaparát, který chcete umístit.

Přejděte dolů a klepněte na “Režim umístění”.

Získejte pohled v reálném čase na videopřehrávač vašeho fotoaparátu a nic jiného.

Odtáhněte kameru tak, jak to chcete. Stále budete mít trochu zpoždění, ale je to nejdéle asi 1-2 sekundy.

Upravte citlivost pohybu fotoaparátu

Podobně jako režim pozic, aplikace také přichází s funkcí nazvanou “Test detekce pohybu” , což usnadňuje jemné doladění citlivosti pohybu bez tónu pokusů a omylů, které by obvykle trvalo několik dní, než aby bylo možné určit.

Chcete-li získat přístup k této funkci, přejděte zpět na stejnou obrazovku, pouze namísto toho vyberete klepnutím na “Test detekce pohybu” pod ním

Odtud se zobrazí posuvník, který vám umožní upravit citlivost pohybu fotoaparátu

Malá modrá LED kamera na přední straně se rozsvítí kdykoli detekuje pohyb při určitém nastavení citlivosti. Jediné, co musíte udělat, je chodit před kamerou, dívat se na rozsvícení modré LED a pak upravit citlivost.

Grafické ovladače společnosti Intel odmítnou instalaci v některých počítačích, i když používají grafické čipy Intel. Pokud se zobrazí tato chybová zpráva, výrobce vašeho počítače chce nainstalovat ovladače z jejich webových stránek, nikoli přímo od společnosti Intel. Existuje však způsob, jak obejít tuto zprávu a nainstalovat ovladače Intel.

Takže jste dostali Amazon Echo, ať už z nedávných prodejů nebo z dovolené. Podívejme se na to, jak to nastavit a jaké užitečné věci můžeš uvést do vašeho Echo. Co je Amazon Echo? Jednoduše řečeno, Echo je hlasově řízený virtuální asistent, který vám umožní ovládat smarthome zařízení, kontrolujte počasí, přehrávejte hudbu, získávejte novinky a další.

Khi định vị hầu hết các camera an ninh, phải mất một thời gian và một chút thử nghiệm và lỗi để thiết lập chúng hoàn hảo. Tuy nhiên, Netgear đã thêm một số tính năng giúp cho quá trình thiết lập dễ dàng hơn nhiều đối với máy ảnh Arlo của nó.

Không quá khó để có được góc chụp hoàn hảo của camera an ninh; bạn phải đoán và sau đó nhìn vào nguồn cấp dữ liệu video trực tiếp để xem bạn đã làm tốt như thế nào. Nếu bạn nghỉ một chút, bạn sẽ thực hiện một số điều chỉnh.

Tuy nhiên, điều chỉnh độ nhạy chuyển động có lẽ là quá trình khó khăn nhất, vì có thể mất một vài lần cố gắng để có được nó ngay cả từ xa nơi bạn muốn. Tuy nhiên, với máy ảnh Arlo của Netgear, có những tính năng trong ứng dụng giúp việc cài đặt và định vị máy ảnh dễ dàng hơn rất nhiều.

Đầu tiên, tìm địa điểm lý tưởng để gắn máy ảnh của bạn

Trước khi chúng tôi đi sâu vào các tính năng định vị trong ứng dụng Arlo, máy ảnh cần phải được gắn ở đâu đó (rõ ràng).

Chỉ bạn mới có thể có phán đoán tốt nhất khi tìm nơi tốt nhất để đặt máy ảnh Arlo của mình, vì mỗi ngôi nhà đều khác nhau. Tuy nhiên, Netgear đưa ra một số gợi ý của riêng họ, chẳng hạn như đặt máy ảnh lên cao và đặt nó xuống một chút.

Bạn cũng có thể đặt nó lên trên giá vì máy ảnh có đáy phẳng. Chỉ cần đảm bảo rằng giá không quá cao, vì cuối cùng bạn sẽ nhận được nhiều trần hơn trong khung, thay vì các bit quan trọng.

Sử dụng Chế độ vị trí của ứng dụng

Arlo có một tính năng dành riêng cho việc định vị máy ảnh để giúp đạt được góc nhìn tốt nhất có thể mà không có bất kỳ ma sát nào. Chế độ vị trí, như được gọi, cố tình làm giảm chất lượng của nguồn cấp dữ liệu video để giảm thời gian trễ, vì vậy khi bạn di chuyển camera xung quanh để định vị nó, bạn sẽ thấy chế độ xem gần thời gian thực trong ứng dụng.

Để truy cập tính năng này, hãy mở ứng dụng Arlo trên điện thoại của bạn và nhấn vào tab Cài đặt cài đặt ở góc dưới bên phải.

Chạm vào trên các thiết bị của tôi.

Chọn máy ảnh mà bạn muốn định vị.

Cuộn xuống và nhấn vào Chế độ định vị.

Bạn sẽ có chế độ xem thời gian thực của nguồn cấp dữ liệu video của máy ảnh của mình và không có gì khác.

Từ đó, định vị máy ảnh của bạn như thế nào bạn muốn nó. Bạn vẫn sẽ có một chút độ trễ, nhưng tối đa chỉ khoảng 1-2 giây.

Điều chỉnh độ nhạy chuyển động của máy ảnh

Tương tự như Chế độ định vị, ứng dụng cũng đi kèm với một tính năng có tên là Chuyển động phát hiện chuyển động, giúp điều chỉnh độ nhạy chuyển động dễ dàng hơn mà không cần quá nhiều thử nghiệm và thường sẽ mất vài ngày để xác định chính xác.

Để truy cập tính năng này, hãy quay lại cùng màn hình nơi bạn đã chọn Chế độ vị trí, chỉ thay vì chọn tính năng đó, hãy nhấn vào Kiểm tra phát hiện chuyển động của Di động bên dưới nó.

Từ đó, bạn sẽ thấy một thanh trượt cho phép bạn điều chỉnh độ nhạy chuyển động của máy ảnh.

Đèn LED nhỏ màu xanh của máy ảnh ở mặt trước sẽ sáng lên bất cứ khi nào nó phát hiện chuyển động ở một cài đặt độ nhạy cụ thể. Vì vậy, tất cả những gì bạn phải làm là đi bộ trước máy ảnh, xem đèn LED màu xanh sáng lên, sau đó điều chỉnh độ nhạy cho phù hợp.

The makers of Arlo cameras have done their best in ensuring the safety of this device from random snooping or hacking.

However, security measures can only work up until they are breached by some bad actors. One of the best ways to prevent a breach is to reverse engineer a system to find out possible flaws.

So learning how to hack Arlo cameras is a pre-requisite of being double sure about its safety and security from any possible digital threat.

The manufacturers of these security cameras swear on their immunity from any such hacking or snooping. But, as the base station of the Arlo security camera communicates to the camera devices via wifi, there’s always a potential threat from hackers in the process.

Here, we discuss some of the most common ways to hack the Arlo pro cameras. Knowing them, you can easily stay prepared for any such snooping or hacking threat to your Arlo camera.

Methods and ways regarding how to hack Arlo cameras

Step 1. Getting access to the default password

No matter if it’s the Arlo security camera or a standard wireless security camera, you can easily hack into the device by gaining the access to the default password.

To go ahead with the task, you just need to look for the IP address of the security camera.

Once done, you can look out for random websites around that can help you with the signup information regarding the Arlo security cameras.

Moreover, certain Password engines can provide you with a customized list of the most commonly used passwords from these devices.

This happens when most of the Arlo security camera owners don’t think of changing the password of their security camera. This is where they allow all the hackers to snoop into their devices without any hassle.

So, it doesn’t matter whether you are a professional hacker or else, you can try this trick and get access to the device’s password which will then take it to the remote access of the entire Arlo security system without any issue.

Step 2. Getting access to the user-id

If you are unable to find any success with the device password, you can then look up to hack the Arlo security camera by checking for the default user ID.

Just like the default password, most of the Arlo security camera owners forget to change the user ID and this is where they leave a loophole for the hackers to sneak in.

If you get access to the user ID, you can check into the entire security system and further reset the account accordingly.

Most of the professional hackers have confirmed the fact that once you have the user ID, sneaking into the user’s phone numbers, email or any other information is as easy as sipping a cup of coffee.

Once you get access to the user ID of the Arlo security camera, you can easily reset all the general information and can gain full control over the security system associated with that specific user ID.

Even though the makers have brought certain improvisations and security protocols to the existing Arlo devices, there’s always a way to sneak into them using this method.

Step 3. Checking into the command line of codes

There are certain Arlo security camera owners then doesn’t feel the need for updating the security systems with the latest firmware.

Hence, the hackers are offered an easy passage to sneak into the device by simply tracking or monitoring the given command line of codes.

Quite recently, one of the world’s most recognized makers of security devices gets to know about certain flaws within their security cameras.

Even though immediate actions were taken to track and correct the issue, it raised a lot of eyebrows regarding the safety and security of these devices.

People were concerned about the fact that a device that assures them of the safety and security of their valuables and assets got its security glitches to deal with.

Step 4. Hacking the wifi device

Just in case you are unable to hack the Arlo security cameras, you can further try to sneak into the wifi device by using the methods mentioned above.

No matter how secured the device is, they always communicate by exchanging certain codes via wifi to the connected units.

So, once you have remote access to the wifi connection, you can easily snoop into the entire security system.

Bottom-line for How to hack Arlo cameras

Hacking is an illegal act and one must think twice before getting into any such activity, irrespective of the purpose and reasons.

Still, the methods mentioned above can be used as an ‘eye-opener’ and the owners of the Arlo cameras can then pay special attention while creating the User IDs and Passwords of the security cameras.

Når du placerer de fleste sikkerhedskameraer, tager det lidt tid og lidt forsøg og fejl at få dem til at oprette perfekt. Netgear har dog tilføjet nogle funktioner, der gør installationsprocessen meget nemmere for sine Arlo-kameraer.

RELATED: Sådan opstilles Netgear Arlo Pro-kamerasystemet

Det er ikke for svært at få den perfekte vinkel af et sikkerhedskamera du skal tage et gæt og derefter se på live video feed for at se, hvor godt et job du har gjort. Hvis du var ude af en smule, ville du foretage nogle tilpasninger.

Justering af bevægelsesfølsomheden er nok den mest omhyggelige proces, da det kan tage et par forsøg på at få det selv fjernt, hvor du vil have det. Med Netgears Arlo-kameraer er der dog funktioner i appen, der gør installationen og placeringen af ​​kameraer meget nemmere.

Først finder du det ideelle sted at montere dit kamera

Før vi dykker dybt ind i positioneringsfunktionerne i Arlo app, kameraet selv skal monteres et sted (selvfølgelig).

Kun du har den bedste vurdering, når det kommer til at finde det bedste sted at sætte dit Arlo kamera, da hvert hus er anderledes. Netgear tilbyder dog nogle egne forslag, som f.eks. At placere kameraet højt og fyre det lidt ned.

Du kan også bare sætte det oven på en hylde, da kameraet har en flad bund. Bare sørg for, at hylderne ikke er for høje, fordi du ender med at få mere af loftet i rammen end de vigtige bits.

Brug App’ens “Position Mode”

Arlo har en funktion udelukkende til at placere kameraet for at opnå den bedste synsvinkel mulig uden friktion. Positionsmodus reducerer videoformatets kvalitet med det formål at mindske lagretid, så når du bevæger kameraet rundt for at placere det, vises en nærtliggende visning i realtid i appen.

For at få adgang til denne funktion skal du åbne Arlo-appen på din telefon og trykke på fanen “Indstillinger” nederst til højre.

Tryk på “Mine enheder”.

Vælg det kamera, du vil placere.

Rul ned og tryk på “Position Mode”.

Du får en visning i realtid af dit kameras video feed og intet andet.

Placer dit kamera, hvordan du vil have det. Du får stadig lidt forsinkelse, men det er kun ca. 1-2 sekunder.

Juster kameraets bevægelsesfølsomhed

I lighed med positionsfunktionen leveres appen også med en funktion kaldet “Motion Detection Test” , hvilket gør det lettere at finjustere bevægelsesfølsomheden uden et ton forsøg og fejl, som normalt tager nogle dage at bestemme.

For at få adgang til denne funktion, gå tilbage til samme skærm, hvor du valgte Positionsmodus, Kun i stedet for at vælge det, skal du trykke på “Bevægelsestest” under det.

Derfra ser du en skyder, der gør det muligt at justere kameraets bevægelsesfølsomhed.

Kameraets lille blå LED på forsiden lyser når det registrerer bevægelse ved en bestemt følsomhedsindstilling. Så alt du skal gøre er at gå foran kameraet, pas på, at den blå LED lyser og juster følsomheden i overensstemmelse hermed.

Når du har en pc helt inficeret med virus, er det nogle gange bedst at genstarte en redningsdisk og køre en fuld virus scanne derfra. Her kan du bruge BitDefender Rescue-cd’en til at rense en inficeret pc. RELATED: Hvad er det bedste antivirus og hvordan vælger jeg? Det gode ved BitDefender er, at deres regelmæssige antivirus er konsekvent bedømt til toppen med hensyn til detektering og fjernelse af vira, så du må antage, at deres rednings-cd skal fungere godt.

U2F er en ny standard for universelle tofaktors autentificeringstogter. Disse tokens kan bruge USB, NFC eller Bluetooth til at levere to-faktor-godkendelse på tværs af forskellige tjenester. Den understøttes allerede i Chrome, Firefox og Opera til Google, Facebook, Dropbox og GitHub-konti. Denne standard understøttes af FIDO-alliancen, som omfatter Google, Microsoft, PayPal, American Express, MasterCard, VISA, Intel, ARM, Samsung, Qualcomm, Bank of America og mange andre massive virksomheder.

เมื่อวางตำแหน่งกล้องรักษาความปลอดภัยส่วนใหญ่จะต้องใช้เวลาสักครู่ในการทดสอบและข้อผิดพลาดเล็กน้อยเพื่อให้พวกเขาติดตั้งได้อย่างสมบูรณ์แบบ อย่างไรก็ตาม Netgear ได้เพิ่มคุณสมบัติบางอย่างที่ทำให้กระบวนการติดตั้งง่ายขึ้นมากสำหรับกล้อง Arlo.

มันไม่ยากเกินไปที่จะได้มุมกล้องรักษาความปลอดภัยที่สมบูรณ์แบบ คุณต้องเดาแล้วดูฟีดวิดีโอสดเพื่อดูว่างานที่คุณทำดีแค่ไหน หากคุณไม่ได้ใช้งานคุณจะต้องทำการปรับเปลี่ยนบางอย่าง.

อย่างไรก็ตามการปรับความไวในการเคลื่อนไหวอาจเป็นกระบวนการที่ลำบากที่สุดเนื่องจากอาจต้องใช้ความพยายามสักสองสามนาทีเพื่อให้ได้ระยะไกลแม้ในที่ที่คุณต้องการ อย่างไรก็ตามด้วยกล้อง Arlo ของ Netgear มีคุณสมบัติในแอพที่ทำให้การติดตั้งและวางตำแหน่งกล้องง่ายขึ้นมาก.

ก่อนอื่นให้หาสถานที่ที่เหมาะสมในการติดตั้งกล้องของคุณ

ก่อนที่เราจะดำลงลึกเข้าไปในคุณสมบัติการวางตำแหน่งในแอป Arlo กล้องนั้นจะต้องติดตั้งที่ไหนสักแห่ง (ชัด).

มีเพียงคุณเท่านั้นที่จะมีวิจารณญาณที่ดีที่สุดในการหาสถานที่ที่ดีที่สุดสำหรับใส่กล้อง Arlo ของคุณเนื่องจากบ้านทุกหลังแตกต่างกัน อย่างไรก็ตาม Netgear ให้ข้อเสนอแนะบางอย่างของพวกเขาเองเช่นวางกล้องไว้สูงและตกปลาลงเล็กน้อย.

ใช้ “ตำแหน่งโหมด” ของแอพ

Arlo มีคุณสมบัติเฉพาะสำหรับการจัดตำแหน่งกล้องเพื่อช่วยให้ได้มุมมองที่ดีที่สุดเท่าที่จะเป็นไปได้โดยไม่มีแรงเสียดทาน โหมดตำแหน่งที่เรียกว่าลดคุณภาพของวิดีโอฟีดลงเพื่อลดเวลาหน่วงดังนั้นเมื่อคุณเลื่อนกล้องไปรอบ ๆ เพื่อวางตำแหน่งคุณจะเห็นมุมมองใกล้เวลาจริงในแอป.

ในการเข้าถึงคุณสมบัตินี้ให้เปิดแอป Arlo บนโทรศัพท์ของคุณแล้วแตะที่แท็บ“ การตั้งค่า” ที่มุมล่างขวา.

จากนั้นจัดตำแหน่งกล้องในแบบที่คุณต้องการ คุณจะยังคงได้รับความล่าช้าเล็กน้อย แต่โดยทั่วไปจะใช้เวลาประมาณ 1-2 วินาทีเท่านั้น.

ปรับความไวในการเคลื่อนไหวของกล้อง

เช่นเดียวกับโหมดตำแหน่งแอพนี้ยังมาพร้อมกับคุณสมบัติที่เรียกว่า “การทดสอบการตรวจจับการเคลื่อนไหว” ซึ่งทำให้ง่ายต่อการปรับแต่งความไวของการเคลื่อนไหวโดยไม่ต้องลองผิดลองถูกและมีข้อผิดพลาดมากมาย.

หากต้องการเข้าถึงคุณลักษณะนี้ให้กลับไปที่หน้าจอเดียวกับที่คุณเลือกโหมดตำแหน่งเท่านั้นแทนที่จะเลือกนั้นให้แตะที่ “การทดสอบการตรวจจับการเคลื่อนไหว” ด้านล่าง.

ไฟ LED สีฟ้าเล็ก ๆ ของกล้องที่ด้านหน้าจะสว่างขึ้นทุกครั้งที่ตรวจจับการเคลื่อนไหวด้วยการตั้งค่าความไวแสงเฉพาะ ดังนั้นสิ่งที่คุณต้องทำก็คือเดินหน้ากล้องดูให้ไฟ LED สีฟ้าสว่างขึ้นจากนั้นจึงปรับความไวตามลำดับ.

Arlo Camera(s)

An additional camera costs $159.99. Weighing in at 0.25 lbs, the camera is 2.5×1.6×2.8 inches (HxWxD) big. It is small, stylish, glossy-white, oval-shaped and comes with a flat bottom base that makes placing it on a flat surface a breeze. We installed our cameras inside the house and played a treasure-hunting game with our kid. He found it hard to spot the two cameras that were scattered about. The fact that the cameras are wireless makes changing their position every now and then fun and easy and even helpful as those who might spot them—potential thieves—won’t know where the cameras are after you’ve moved them.

This kit also includes mounts with a magnetic ball, each, which allows for the cameras to be placed onto a wall or a tree, for instance. The magnetic ball allows you to turn the camera by 360 degrees, although the camera can also be stolen once spotted since it is only attached (bracket) to the mount via its magnetic ball; place yours high or out of sight in an attempt to keep them safe. You may also purchase another adjustable mount (VMA1000 for $19.99) and screw the camera onto it instead.

Each camera has motion sensors and is IP65 waterproof. At the front are twelve infrared LEDs, and the SYNC button can be found on top. There is no microphone or speaker on the camera, so there is no way to record sound or to communicate, which is a pity since many cameras available on the market today are equipped with a microphone and a speaker to allow for a two-way communication. We would like to see the Arlo kits integrate such a system as well.

These cameras produce a curved image for a larger field of vision. The displayed image has a high definition (HD) resolution you can increase to 1280×720p in a H.264 format, along with a 130 degrees field of vision. We also have 850nm LEDs that illuminate everything at up to 25 feet and IR cut off-filtering capabilities that result in a bright, clear, and crisp image at night. The camera’s motion sensor also detects movement at up to approximately 15 feet, and its sensitivity can be adjusted to your needs. Its 100% setting will even have a small breeze that tips flowers over slightly trigger the email-alert function and a recording. Yet you will have to move your hands around in front of the camera to trigger the sensor if it is set to 1%.

There is no port for a power source on the camera, which makes Netgear’s included lithium batteries the only option. Every camera uses four CR123a (3V) batteries. Netgear states these batteries to approximately last six month at roughly four minutes of daily use so long as some rather energy savvy settings are used. Use its advanced video setting and these batteries will most likely last four months. With a price of $5 (on average) for each battery, such would amount to $120 annually. But you may also use rechargeable batteries in order to reduce the amount of money spent per year. What matters here is a battery’s mAh rating since a higher mAh will result in longer run times based on how much current is drawn. Note that rechargeable batteries might not last as long as non-rechargeable ones because of the reduced voltage they produce. Rechargeables might produce inaccurate power readings with these cameras.

The cameras are water- and weatherproof as they can withstand tough conditions of cold (down to 14 F) and heat (up to 122 F), which, as has already been mentioned, makes them suitable candidates for the outdoors. Each camera has a battery status bar should you want to figure out how much juice a battery has left. The problem here is that the status bar will lie by stating a battery to almost be dead if its surroundings are extremely cold. Netgear is aware of this problem and is said to be working on a solution. The cameras also come with a standard female ¼ adapter if you want to mount them to a tripod.

Base Station

The base is white, its dimensions are 6.5×8.5×2.25 inches (HxWxD), and it weighs in at around 0.25 lbs. It uses Wi-Fi 802.11n at 2.4 GHz and is equipped with a LAN port and two USB 2.0 ports. On it are also a Power button and a Reset switch, along with the SYNC button and power jack in the rear. On its front are several LED-specific status indicators for Power, Internet, Camera, Smart Home, and USB. Netgear says the Smart Home and USB LEDs to be reserved for future use, as compatibility with other smart-home standards is introduced.

Use SmartThings to Monitor Your Home Inside and Out with NETGEAR Arlo Wire-free HD Cameras

SAN JOSE, Calif. — August 30, 2016 — NETGEAR®, Inc. (NASDAQ: NTGR ), the leading provider of smart home security cameras, today announced the Arlo Wire-free HD Security Camera’s integration with Samsung’s SmartThings. The collaboration will enable Arlo Wire-free cameras to interact with devices on the SmartThings platform, while also adding video recording to its Smart Home Monitor security solution.

The Arlo camera makes a great addition to SmartThings Smart Home Monitor as an elegant, and easy-to-use security solution. The camera can be triggered to record video clips by other devices that are part of Smart Home Monitor, such as door, window, or motion sensors. It can also act as a motion detector, to trigger other SmartThings devices, such as turning on lights as a person enters a room or approaches a house.

Accessing Arlo smart cameras within the SmartThings app will make living smart easier than ever. An open platform with a thriving ecosystem, SmartThings brings freedom of choice in devices, and now with the integration of Arlo smart cameras, smart home monitoring has near limitless possibilities. Users may view the live feed from Arlo smart cameras directly within the SmartThings app, right alongside their other devices, offering home monitoring and remote control within a single interface. SmartThings is the easiest way to turn a home into a smart home, with an open platform that has one of the largest ecosystems of compatible devices.

“Arlo’s mission is to deliver products that make it incredibly simple for people to keep an eye on their property, kids, pets and everything else that matters most in their lives,” said Pat Collins, senior vice president of Arlo products at Netgear . “By working with Samsung SmartThings to make our innovative, 100% wire-free, HD smart cameras compatible with their platform, we are now able to offer customers the added benefits of seamless connectivity between Arlo and many other smart devices.”

“Interoperability with the most popular and technically advanced devices on the market is key to achieve mass consumer adoption for the smart home,” said Brett Worthington, General Manager for Americas and Vice President of Global Business Development, SmartThings. “At SmartThings, we’re committed to building an open platform with a robust third party ecosystem, and are excited to deliver our customers even more capabilities with the Netgear Arlo camera integration available today.”

Availability

The SmartThings app is available now and support for Arlo smart cameras is included as of today’s announcement.

About NETGEAR, Inc.

NETGEAR (NASDAQ: NTGR) is a global networking company that delivers innovative products to consumers, businesses and service providers. The Company’s products are built on a variety of proven technologies such as wireless (WiFi and LTE), Ethernet and powerline, with a focus on reliability and ease-of-use. The product line consists of wired and wireless devices that enable networking, broadband access and network connectivity. These products are available in multiple configurations to address the needs of the end-users in each geographic region in which the Company’s products are sold. NETGEAR products are sold in approximately 28,000 retail locations around the globe, and through approximately 29,000 value-added resellers, as well as multiple major cable, mobile and wireline service providers around the world. The company’s headquarters are in San Jose, Calif., with additional offices in approximately 25 countries. More information is available from the NETGEAR investor page or by calling (408) 907-8000. Connect with NETGEAR on Twitter and Facebook .

About SmartThings

SmartThings is the easiest way to turn a home into a smart home, bringing users peace of mind, savings, and convenience. As an open platform with a thriving ecosystem, SmartThings also brings users freedom of choice in devices and limitless possibilities. SmartThings is headquartered in Palo Alto, CA and operates independently as a wholly owned subsidiary of Samsung Electronics.

©2016 NETGEAR, Inc. NETGEAR, the NETGEAR logo, and Arlo are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its affiliates in the United States and/or other countries. Other brand and product names are for identification purposes only and may be trademarks or registered trademarks of their respective holder(s). The information contained herein is subject to change without notice. NETGEAR shall not be liable for technical or editorial errors or omissions contained herein. All rights reserved.

Wireless security cameras that connect to the web and allow you to monitor what’s going on in your home, even when you’re not there, offer an easy way to keep an eye on your home.

Netgear, which launched the Arlo Smart Home Security Camera last year, has unveiled a new version of the security camera called the Arlo Q that not only allows you to see what’s going in your home, but also listen to what’s going on and even talk back, making it ideal for talking to your pets, answering your kids’ homework questions, or scaring off an intruder.

The Arlo Q can be used on its own, or connected to an existing Arlo system if you already have one, and it has a 4MP image sensor and built-in night vision to ensure you can see the video captured by the camera in HD so it’s clear and sharp. To see what’s going on in your home at any point, just open the smartphone or tablet app and you’ll be able to see and communicate with those in your home.

Furthermore, footage is stored in the cloud for up to seven days at no charge so you can also open the Arlo app on your smartphone or tablet and view the footage from earlier in the day or week, and if any motion is detected in your home, the Arlo Q camera will alert you with a notification in the app or an email.

The Arlo Q Camera has a 130 degree angle, which Netgear says means you can see entire rooms from corner to corner but unlike the original Arlo, the Arlo Q is mains-powered rather than battery powered, so you will need to position the camera near a power outlet.

The GHI team are fans of wireless cameras for the home, as it’s great to keep an eye on what’s going on even when you’re not there, but the addition of the two-way communication is even better. We look forward to putting the camera to the test very soon.

Netgear’s Arlo security system is the company’s first foray into a rapidly growing DIY home security market. Comprised of the usual feature set we’ve come to expect of such systems like night vision and motion detection Arlo takes things a step further by introducing wireless HD cameras. Each camera streams a 720p image and has a 110 degree field of view. They’re also completely weather proof and can operate solidly up to 25m from the Arlo base station.

Wireless you say? Feature rich you say? I can’t wait for the part you talk about how bad the battery life is…? Well let’s get it out of the way. It’s good. In fact it’s better than good, it’s four to six months good! Actual battery life will depend on the way you use the cameras in your setup though. Night vision means powering LEDs, continually recording or streaming means a large draw and the constant monitoring of motion will contribute too but after a month of what I’d consider “normal home security usage” both of my cameras are still at full power.

Each camera takes four CR123 batteries, which Netgear kindly include. They’re stubby short little buggers that if I’m being honest I’d never seen the before. Apparently they’re common in flashlights, so when it comes to buying replacements they shouldn’t be too hard to find. Rechargeable versions apparently work too according to forum posts I came across but they’re not mentioned anywhere in the documentation and will, due to the nature of rechargeables, result in a slightly shorter life than regulars.

The great thing about the Arlo system is just how easy they’ve made it to get it up and running. The brain of the system, a closed 802.11n wifi base station is connected to your internet’s router/modem via ethernet. Once it’s established a link back to the Arlo servers you’re ready to start connecting your cameras. This is done by pressing a “sync” button on both the camera and base station simultaneously for a short period of time until lights flash on both devices. It really couldn’t be any easier and I’m glad this physical approach is effectively handling the setup of the remembered wireless network connection happening behind the scenes further simplifying the installation process.

As the cameras are wireless you can position them anywhere within range of the base station. Indoors or out, low or high the options are limitless and honestly is what sells the system. To further extend the positioning options beyond simply sitting the camera on a surface each has a strong magnet in its rear. This coupled with an included mounting disc that can be placed on a wall or ceiling allows you to magnetically position the camera and move it to whatever angel you require.

The system is controlled via the Arlo app which is available for both iOS & Android. After going through the normal account creation motions you arrive at the main interface for controlling your Arlo setup. It’s here you’ll see a recent view from each of your connected cameras along with their current connection, battery life and motion sensor status.

The general operation and configuration options of the cameras are on par with Arlo’s competitors. For a product that’s pushing boundaries with its hardware the lack of innovation software wise is rather uninspiring and feels to be a let down in some ways. You’ll find options to control the scheduling of motion detection, “rules” that are really nothing more than who to email/notify when motion is detected and the ability to limit motion detection to a portion of the image instead of its entirety, as well as a few other but nothing particularly unexpected.

General use involves having the cameras setup to record once motion is detected for 10 seconds. The footage is then immediately uploaded to the cloud and if selected an email sent to notify you of the recording. This follows the current trend in similar products, utilising cloud storage to effectively provide offsite storage for you.

Cloud storage is all well and good providing your internet connection is operating at the time someone is robbing your home but the continual lack of local storage as an option in addition to cloud for all of these new wave of security products is slightly concerning. The privacy conscious are likely to not consider Arlo and many of its counterparts if only because it is a cloud reliant product. The hope, with the Arlo system at least, is that local storage is an option is to come. The included base station has two USB ports on it making it a real possibility down the track but Netgear are yet to confirm anything, including why those ports are there at all.

Another downside of a cloud only solution is the cost. Luckily a free tier will suit almost everyone’s needs supporting up to 5 cameras with 1GB of storage for recordings captured over the last 7 days. A “premier” & “elite” tier (A$13 & A$19 per month respectively) extended your storage capacity (10GB, 100GB) and archive days (30, 60) whilst allowing up to 15 cameras at the top level.

Recordings as well as streaming of the cameras’ current view can by done via the Arlo app or the web. The web interface mimics the app in most ways and configuration options can be tailored here too. In fact I actually found the web interface to be more responsive and easier to use than the app but really once you’ve got things where you want them it’s kind of set and forget.

Absent from the Arlo system is an audio interface. Unlike its main competitor Nest Cam (formerly Dropcam) the Arlo cameras have no microphone or speaker meaning you’re unable to communicate through them. You might think you have no need to do this but for those using it to say monitor their pets whilst at work, yelling at them may just stop them from ripping that new cushion to shreds. The Arlo won’t help you here.

Also missing – and a feature that I and seemingly everyone else on the Netgear forums is screaming for – is IFTTT integration. Arlo, along with Nest Cam, have no API or 3rd party integration of any kind at this stage. Nest currently have their smoke detector and thermostat working with IFTTT so it’s likely only a matter of time but for Arlo there’s no mention anywhere that it’s going to come. Without it things like geofencing your home to automatically toggle the cameras’ motion detection function are impossible. Making the a Philips Hue or LIFX bulb turn on as the recording begins, again, not to be.

As far as DIY security systems go the Arlo is by far the most convenient on the market today. Its wireless cameras allow for an almost infinite array of positioning options and the setup of the system is almost instantaneous. The trade off for such convenience: a lack of audio support and a slightly lower image quality than some of its competitors who offer 1080p. Is that enough to sway the majority of people away? I seriously doubt it.

Jei turite “Netgear” “Arlo Pro” fotoaparato sistemą, visiškai bevielės galimybės, be abejonės, jums gerai tinka.

SUSIJĘS: Ar turėtumėte įsigyti “Wi-Fi” kamerą su baterijomis?

“Arlo Pro” sistemareikalingas centrinis mazgas, kuris įjungia jūsų maršrutizatorių, tačiau be to, visi jūsų nustatytos kameros gali būti visiškai bevielis, nes jie veikia su baterija ir naudoja “Wi-Fi” duomenų perdavimui. Bet čia yra keletas kitų funkcijų, apie kurias galbūt norėsite žinoti.

“Mount & Position” fotoaparatai greitai ir lengvai

SUSIJĘS: Kaip pastatyti “Netgear Arlo” fotoaparatus “Easy Way”

Tai gali būti šiek tiek sunku kamerą puikiai nežiūrint į tiesioginį vaizdą, ypač kai yra šiek tiek atsilikimo. Tačiau “Arlo Pro” turi “padėties režimą”, kuris padeda šiais atvejais.

Tiesiog eikite į “Nustatymai”> “Mano įrenginiai” ir pasirinkite fotoaparatą. Tada palieskite “Pozicijos režimas”. Jūs gausite tiesioginį vaizdo įrašą apie fotoaparatą, kuris yra šiek tiek labiau reaguoja ir mažiau laggy, todėl fotoaparatas gali greitai nejudėti.

Bendrinkite pasiekiamumą su kitais namų ūkio nariais

SUSIJĘS: Kaip pasidalinti priėjimu prie savo “Netgear” “Arlo” fotoaparatų

Jūs tikriausiai nėra vienintelis jūsų namuose, kuris galėtų gauti įspėjimus ir pamatyti tiesioginį “Arlo” kamerų vaizdą. Geros naujienos yra tai, kad galite dalytis prieiga su kitais žmonėmis.

Tiesiog atidarykite “Arlo” programos nustatymus ir bakstelėkite “Grant prieigą”. Iš ten galite pakviesti kitų namų ūkio narių, norėdami gauti “Arlo” programą ir pasiekti savo namų kameros sklaidos kanalus.

Patobulinkite baterijos tarnavimo laiką

SUSIJĘS: Kaip padidinti “Netgear Arlo Pro” fotoaparatų baterijos tarnavimo laiką

Jūs gali palikti savo “Arlo” kamerą prijungtą taip, kad jums niekada nereikės jų įkrauti, tačiau jei jūs juos išvalysite nuo baterijos, gali būti naudinga kuo ilgiau atlikti mokestį.

Yra keletas dalykų, kuriuos galite padaryti, pvz., Sumažinkite vaizdo įrašo kokybę, išlaikykite fotoaparatą nuo šalto aplinkos, įsitikinkite, kad turite stiprų “Wi-Fi” ryšį ir dar daugiau.

Atsisiųsti įrašus į savo telefoną

SUSIJĘS: Kaip atsisiųsti įrašus iš savo “Netgear” Arlo kamerų

Jei yra tam tikras įrašas, kurį norite išsaugoti, “Arlo” “Pro” sistema leidžia tai padaryti. Tai puiki funkcija naudoti, nes vaizdo įrašai nebus saugomi debesyje amžinai.

Tiesiog atidarykite “Arlo” programą ir bakstelėkite “Biblioteka” apačioje. Iš ten pasirinkite įrašą ir apačioje paspauskite “Atsisiųsti”.

Įrašyti vietinius įrašus kaip atsarginę kopiją

SUSIJĘS: Kaip įrašyti “Netgear Arlo Pro” vaizdo įrašą į USB įrenginį

Jei norėtumėte turėti tik visus vietoje įrašytų įrašų į “flash” diską arba standųjį diską, galite tai padaryti ir taip. Įrašai vis tiek bus įrašomi į debesį, taigi pagalvokite apie tai kaip apie atsarginių kopijų metodą.

“Arlo Pro” sistemai pirmiausia reikės formatuoti diską, tačiau po to galite pereiti į “Nustatymai”> “Mano įrenginiai”> pasirinkite pagrindinę

Sukurkite individualius įrašymo režimus

SUSIJĘS: Kaip redaguoti ar kurti “Netgear” “Arlo Pro” fotoaparato sistemos nustatymus

Pagal numatytuosius nustatymus yra Nėra įrašymo režimo, leidžiančio “Arlo” fotoaparatams įrašyti judesį, bet nesiunčiamas įspėjimas, taigi naudinga kurti savo pasirinktinius įrašymo režimus.

Norėdami tai padaryti, bakstelėkite pagrindiniame ekrano apačioje esantį “režimai” pasirinkite savo bazinę stotį, tada bakstelėkite “Pridėti režimą”.

Pervardykite fotoaparatus

SUSIJĘS: Kaip pervardyti “Netgear Arlo” fotoaparatą

Kai pirmą kartą nustatote “Arlo Pro” fotoaparatą, jie ” jie yra pavadinti pagal jų serijos numerius, o tai tikrai nėra naudinga. Laimei, galite kameras pervardyti į bet ką norite.

Tiesiog nueikite į “Nustatymai”> “Mano įrenginiai” ir palieskite fotoaparatą, kurį norite pervadinti.

Išjunkite fotoaparato mikrofoną

SUSIJĘS: Kaip išjungti mikrofoną savo “Netgear” “Arlo Pro” fotoaparate

Tikriausiai jūs neturite Nebūtina, kad kai kuriuose “Arlo” fotoaparatuose būtų įjungtas mikrofonas, bet, laimei, galite išjungti mikrofoną, jei norėsite ir galbūt išmoksite akumuliatoriaus naudojimo laiką.

Eikite į “Settings”> “My Devices” ir bakstelėkite norimą fotoaparatą. išjungti mikrofoną. Iš ten pasirinkite “Audio Settings” ir išjunkite mikrofoną. Iš to paties ekrano taip pat galite išjungti fotoaparato garsiakalbį.

Atidarykite užduočių tvarkytuvę “Windows 10” ir pamatysite, kaip veikia “Application Frame Host” fonas. Šis procesas turi failo pavadinimą “ApplicationFrameHost.exe” ir yra “Windows 10” operacinės sistemos dalis. SUSIJĘS: Kas yra šis procesas ir kodėl jis veikia mano kompiuteryje? Šis straipsnis yra dalis mūsų tęstinė serija, paaiškinanti įvairius procesus, rasti Task Manager, kaip “Runtime Broker”, svchost.

“Snapchat”, kuriame yra išnykusi nuotrauka, yra paprasta programa žmonėms piktnaudžiauti. Vieno sekundės Snap gali būti gana traumuojamas ir neįmanoma įrodyti, kad įvyko; nebent esate pakankamai greitas, kad pamatytumėte ekrano kopiją, jis praeina, kai tik pažvelgsite į jį. Jei kas nors jus priekabina Snapchat, štai kaip juos užblokuoti.

Ever wondered what your dog gets up to when you’re at work? Or perhaps you’re curious as to how often your cat wanders into the back garden. Or you want to check what’s going on at home to make sure there are no burglars about. (And even set a siren going if you see them, but I’ll come to that later.)

All these are reasons why the home security camera market is booming. There are products from Google, Logitech, D-Link, Netatmo and more, but here we concentrate on the popular Netgear Arlo Pro Smart Security System.

You can buy the system with a single camera or up to six, but the three-pack will make sense for most houses – that way you can watch the front door, an inside room and the garden. Note the Arlo and Arlo Pro are both weatherproof, but many home security cameras are designed for indoor use alone.

The way the Pro works is simple. There’s a base station in the box, which you need to connect to your broadband router: Netgear supplies the Ethernet cable, so this is easy enough. Plug it in, power it on.

The Arlo Pro comes with up to six cameras, each of which pair with the base station that you connect to your router.

Note that the rechargeable batteries in the Arlo Pro cameras come charged, lasting for several days before you’ll need to charge them using the supplied charger and microUSB cable. (Lifting up a tiny rubber flap at the rear of the cameras reveals the port.)

So everything’s switched on, ready. Time to connect.

Connecting the Arlo Pro

Rather than communicate via your wireless network, the cameras instead connect wirelessly to the base station. They don’t come ready-paired, so you’ll need to this yourself. It’s easiest to do so via the Android or iOS app, but there is a web-based system if you prefer.

It only takes a minute for each camera to be paired, but note you’ll need to be within reach of the base station so you can press a button on it.

And now you come to the enjoyable bit: setting up your cameras.

If we concentrate on the dog scenario, then you probably want to do three things: hear it; talk to it; make sure it doesn’t jump on the sofa.

If you have a handy flat surface such as a bookcase opposite the sofa then this is probably your best location choice. That way you’ll be close enough to hear the dog easily, but not so easy to reach that it’s tempted to grab the camera in its jaws.

Your next-best option is to wall-mount the Arlo Pro. Now this isn’t something I’ve yet done myself, but all you need – aside from the drill to make the requisite hole in the wall – is in the box.

The Pro has a magnetic, concave hole at its rear, and once you fix the wall mount (and its clever circular nodule, which plugs into the concave hole) you can swivel the camera into position.

Once you attach the wall-mount, the Arlo Pro slots into position magnetically (and firmly).

Using the Arlo app

From this point on, the app is your friend. It allows you to set up different modes to control whether motion detection is switched on – for example, “Disarmed” means motion detection is off, or you can geofence it based on your location.

Fido, get off the bed! Off, Fido, off!

You can also set it to zoom. Let’s say you only want to capture the sofa: there’s a setting where you can “pinch and zoom” on the image to make that the active area of the image.

You can always view the footage live, but you may prefer to select motion detection. This will capture ten seconds of video each time something appears, and you choose to get an alert each time if you so wish.

What about when you want to talk to the dog? Press the Devices tab, select the camera you’re interested in and hit the mic icon. A green button will appear, which you hold down to speak – exactly like a walkie-talkie. And, just like a walkie-talkie, you won’t be able to hear your dog barking while you talk to it.

Should burglars appear and your dog’s bark isn’t proving enough of a deterrent, there’s always the last resort: click Turn Siren On and watch them run. And trust me, run they will: that siren makes one heck of a noise.

Through simple voice commands, you can now view the live or recorded video feed from your Arlo Security Camera on the screen of the new Amazon Echo Show

June 22, 2017 09:00 ET | Source: NETGEAR NETGEAR

San Jose, California, UNITED STATES

SAN JOSE, Calif. , June 22, 2017 (GLOBE NEWSWIRE) — NETGEAR®, Inc. (NASDAQ:NTGR), the leading provider of networking devices that power today’s smart home, is introducing voice commands for its market-leading Arlo® Family of Smart Security Cameras through the Amazon® Alexa™ voice service.

The Amazon Alexa voice service has become a popular command center for today’s smart home. And now, using the Arlo Skill for Alexa, you can ask Alexa to view the live feed or recorded video from an Arlo camera on the screen of the new Amazon Echo Show™. With a simple voice command you can now ask Alexa to show, the front door, back yard, the driveway, and anywhere else an Arlo camera has been placed. With the Alexa skills you will no longer need to navigate the Arlo app or have your mobile device in hand each time you wish to view an Arlo camera.

With brilliant HD video quality, two-way audio, live streaming, 7 days of free cloud recordings, instant alerts, and other smart features, Arlo Smart HD cameras enable you to watch over what you love from every angle, indoors and out, day and night. To take advantage of the new voice command viewing feature, you need a supported and connected Arlo camera and an Echo Show.

Arlo devices that currently support the Arlo Skill include:

  • Arlo Wire-Free (Model VMC3030, VMS3x30)
  • Arlo Q (Model VMC3040)
  • Arlo Pro (Model VMC4030, VMS4x30)
  • Arlo Go (Model VML4030)
  • Arlo Baby (Model ABC1000)

“Alexa makes a natural companion to Arlo, and vice-versa,” said Pat Collins, senior vice president of Arlo products at NETGEAR. “NETGEAR has always emphasized the ease-of-use in our products, and the support of Alexa voice commands through the Arlo Skill makes it easier than ever to view your Arlo security video recordings. We’re excited that our customers will be able to call up their video recordings anytime, hands-free, to display on the Amazon Echo Show screen. It’s bringing us one step closer to the Jetsons-style home.”

Sample commands in the Arlo Skill set include:

  • “Alexa, show me the front door.”
  • “Alexa, show me the baby room.”
  • “Alexa, hide the baby room.”
  • “Alexa, go home.”

NETGEAR products are available in major retail stores and online. For information about Amazon Alexa integration with other NETGEAR products including Nighthawk® routers and the Orbi™ Tri-Band Home WiFi System, please visit the NETGEAR.com/Alexa landing page.

About NETGEAR, Inc.
NETGEAR (NASDAQ:NTGR) is a global networking company that delivers innovative products to consumers, businesses and service providers. The Company’s products are built on a variety of proven technologies such as wireless (WiFi and LTE), Ethernet and powerline, with a focus on reliability and ease-of-use. The product line consists of wired and wireless devices that enable networking, broadband access and network connectivity. These products are available in multiple configurations to address the needs of the end-users in each geographic region in which the Company’s products are sold. NETGEAR products are sold in approximately 31,000 retail locations around the globe, and through approximately 28,000 value-added resellers, as well as multiple major cable, mobile and wireline service providers around the world. The company’s headquarters are in San Jose, Calif., with additional offices in approximately 25 countries. More information is available from the NETGEAR investor page or by calling (408) 907-8000. Connect with NETGEAR on Twitter, Facebook and our blog.