Categories
Device

How to clean a brita water bottle

Confused on if your water bottle mouthpiece is dishwasher safe? qunchingyourthirst.com has a simple procedure on how to clean your water bottle mouthpiece without using a dishwasher.

What You’ll Need To Clean Your Water Bottle Mouthpiece

To ensure you thoroughly clean your water bottle mouthpiece, we suggest using the following:

  1. Warm water
  2. Liquid dish soap
  3. Scrub sponge
  4. Straw brush – only required for additional step as seen below

Cleaning the Mouthpiece

  1. Fill your sink about one-quarter full of warm water.
  2. Squirt a small amount of liquid dish soap into the water.
  3. Place the mouthpiece in the soapy water for about 5 to 10 minutes.
  4. Next, give the mouthpiece a good scrub with a damp scrub sponge, ensure you make contact with the whole surface area of the mouthpiece. This helps remove any grime that has built up during use.
  5. As an additional step, you can use a small bristle straw brush to clean the spout and drinking hole on the mouthpiece. Run a damp, soapy, straw brush up and down the inside of the drinking hole.
  6. Finally, hold the mouthpiece under flowing, warm water and rinse. Be sure to rinse until all soap-suds have been washed away.

Check-out the list of the products we recommend to help keep you hydrated throughout your day.

Drying The Water Bottle Mouthpiece

After you have completed cleaning your water bottle mouthpiece as per the instructions above, place the mouthpiece on a drying rack or hand-towel. Within 30-minutes your mouthpiece will be dry.

Side Note – Mouthpiece Dishwasher Safe

Consult your water bottle manufacturer for confirmation, but as a side note, most water bottle mouthpieces are top-rack dishwasher safe.

Conclusion

In this article, we reviewed how to clean your water bottle mouthpiece. If you don’t have a dishwasher, or you are unsure if your water bottle mouthpiece is dishwasher safe, follow the simple procedure outlined above.

For any comments, questions or feedback you might have, please send us a message through our contact form.

How to Clean a Brita Water Bottle

It is erratic to think that you don’t have to clean your Brita pitcher. After all, it holds nice clean water in the bacteria-free environment of the refrigerator. However, anything that is uninterruptedly exposed to water and human usage, it would get dirty. You will notice smudges, yes! Shocking mold! It is effortless to overlook this device when cleaning our refrigerator or kitchen. Hence the Brita pitcher doesn’t get the hygienic attention for it to do what it does best. The Brita is something we use every day, so it must be cleaned from time to time.

There are apparent choices below, easy and quick. Cleaning the Brita shouldn’t be too much problem. Once you know and get used to the various ways to clean a Brita pitcher, you will not overthink about it during the next cleaning day.

Note that these options can be applied cleaning any other water filter pitcher and water coolers , so, it’s not necessarily only for the Brita pitcher.

# Preview Product Price
1 How to Clean a Brita Water Bottle Brita Water Pitcher with 1 Filter, w 1 std, White $27.99 Buy on Amazon
2 How to Clean a Brita Water Bottle Brita Water Pitcher with 1 Filter, BPA Free, 5 Cup, White $19.99 Buy on Amazon
3 How to Clean a Brita Water Bottle Brita Ultra Max Filtering Dispenser, Extra Large 18 Cup, Black $31.88 Buy on Amazon

How To Clean A Brita Pitcher

Much is not required cleaning a Brita pitcher; it is easy as washing any other kitchen dish, all you need is the share force of will, the awesome power of determination, and the chilling desire to take hygiene to the next level

Things You Will Need

  1. Sponge
  2. White vinegar
  3. Water
  4. Measuring cups
  5. Drying rack or a dish towel
  6. New filter

Steps for Cleaning a Brita pitcher.

  • Disassemble the Pitcher: pour any water remaining inside the pitcher and disassemble the pitcher. You have to separate the special tank in the Brita filter. If you haven’t changed the screen before, you have to do that. It is only proper hygiene to throw away the filter from time to time, because the filter could just be keeping the bacteria for you and other harmful substances, if you insist on keeping the screen, it is not imperative to wash the screen all you have to do is. Rinse with warm water and place it on a clean surface to prevent it from being contaminated.

Disassembling a Brita filter might be a bit tricky when you want to clean the inside. It is crucial to fill the bottom with water so that the base is heavy, keep it inverted. The weight of the water should pop the plastic inserted pop out.

The type of water filter you buy is going to determine how easy disassembling is going to be. For example, the zero water pitcher is quite popular because of the ease it takes washing them.

  • Wash: you have put the pitcher apart to clean them. Pour out some dish soap in warm water to produce a cleaning solution. Drench the lid and the reservoir for between thirty minutes to one hour. Then scrub each of the independent pieces until you are satisfied that they are clean, and you hear the squeak.
  • Note: that you can as well choose to wash the reservoir with a mild detergent and warm water ending with a gentle dry with a soft towel.
  • Scrape the Mildew: after cleaning the pieces, it is virtually impossible for the mildew to be felt, especially when you clean them thoroughly. If you still there might be mold left, mix white vinegar (a teaspoon) with water (a cup) in a bowl then place the pieces in this solution and scrub.
  • Rinse and Dry: when you have felt for no mildew, and you can hear it squeak. Rinse both the reservoir and the lid in water; do this thoroughly. Place alternatively in lukewarm water. Then keep them to air dry; you have to make sure every part is thoroughly dry before you place them back together, to avoid mildew growing in the pitcher. It is recommended you keep the pieces on the rack. You can also set the part upturned on the dishtowel.
  • Preparing the new Filter: as the pitcher is left in the open to dry, it is time to prepare the new screen for now. Based on the brand of the Brita pitcher you are using, there might be no need to soak the Brita filter before washing. The newer versions of Brita filter do not require for you to soak before wash like the older version. So before washing, you have to check the instructions that come with your particular brand of Brita filter.
  • Putting the Pitcher Together: the pitcher is dry, and the screen is ready, this is the time to reassemble the pitcher back together. Pour water to the brim of the pitcher and disperse after to get rid of any remaining carbon dust. This should be repeated twice at least. Make sure you see that the water is clear before you stop this means that the water is carbon-free. The brand of Brita pitcher you are using determines if you have to go through any additional steps reassembling the pitcher together.

All of our products are built to last a long time. With a little care and attention along the way you can help ensure your Brita® product lives up to its full potential. We’ve also included details on when to replace your filter, how to read your filter change indicators, and details about your product warranty.

Learn more about:

Soaking & Flushing Filters

For pitchers, you should soak your filter before inserting it:

  • Wash hands with soap and water, then remove filter from filter bag.
  • Soak the filter upright in cold water for 15 minutes.
  • Hold filter upright under cold, running tap water for a few seconds.

Faucet Filters
Faucet filters don’t require soaking, however, the system does need to be flushed for five minutes to activate the filter media and remove any carbon dust. The 378-litre filter life begins AFTER flushing for five minutes so you are not wasting filter life by the flushing process.

Brita® Bottles
Bottle filters don’t require soaking. Squeeze one full bottle of water through the filter before use to activate. It’s normal for black carbon dust to appear.

Cleaning

Brita ® Pitchers and Dispensers are very low maintenance when it comes to upkeep and care. You can simply hand wash the lid and reservoir with a mild detergent.

If you have a Brita ® Chrome Pitcher lid, wipe with a soft sponge soaked in a solution of one teaspoon of white vinegar in a cup of water.

Brita ® Bottle: The bottle, the small push-pull cap, large screw-on cap and the finger loop are dishwasher safe (top shelf only). Or like pitchers and dispensers, you can hand wash the Brita ® bottle with a mild detergent.

Pitcher filters should be kept in the sealed Brita ® bag and stored in a cool, dry place until you’re ready to use them. Remember to soak the filter for 15 minutes prior to using.

If your Brita ® Faucet Filter has not been used for several days, you should let water run through the filter for 30 seconds before use, in order to wet and reactivate the system’s filter.

For your Brita ® bottle, squeeze one full bottle of water through the filter before use to activate. It’s normal for black carbon dust to appear

Things to avoid

  • Hot water : Don’t filter water that is over 38°C/100°F. Hot water may release some contaminants that could be found in your tap water. Also, running hot water through the unit can severely diminish the system’s filtration abilities. If this happens, you should replace your Brita ® faucet filter to ensure you enjoy all of the benefits of Brita filtration.
  • Well water : Don’t use water filtration systems with well water that isn’t regularly tested to be microbiologically safe. This filter is intended to be used only with municipally treated tap water or well water that is regularly tested.
Replacing Your Filter

For optimum performance, it’s important to change your Brita® filter on a regular basis. Fortunately, Brita® replacement filters are inexpensive.

Pitchers and Dispensers: Replace filters every 151 litres or every two months for the average family.

Basic Brita® Faucet Filtration System: Replace filters every 378 litres.

Complete Chrome Faucet Filtration System: Replace filters every 378 litres or every four months, whichever comes first.

Brita® Bottles: Replace filter every 256 servings, 151 litres or roughly every two months. Brita sells filters in grocery, drug, discount, specialty, hardware and warehouse club stores. To find a local retailer, please visit our Where To Buy page.

Attaching Your Brita® Faucet Filtration System

Determine if your faucet has threads on the outside or inside. If on the outside, you probably do not need to use an adapter. The base system can most likely be attached directly to the faucet (consult your Users’ Guide). Pick up the base unit, align with the faucet threads and carefully attempt to connect the system to the faucet. If the threads are on the outside, but you can’t get the collar onto the faucet, you may need a special adapter. To receive a special adapter free of charge, call 1-800-387-6940.

If the faucet has inside threads, try using one of the two adapters that come with the system, and attach the base system to the adapter. If neither one of the adapters provided will attach to the faucet, you may need a special adapter. To receive a special adapter free of charge, call 1-800-387-6940.

Setting up Your Indicator

Setting up an Electronic Filter Change Indicator (Complete Pitchers only)

  • If you’ve purchased one of our Brita® Smart Pitchers, the electronic indicator will tell you when to change your filter. To get the indicator light working, follow these easy steps:
  • Press firmly and hold start button for 5 to 10 seconds.
  • Four bars will appear in the display, one after the other, and flash.
  • Do not release the start button until the 4 bars appear and start to flash. If you have difficulty pressing the start button, a capped ballpoint pen may be used to press the button down.
  • A small flashing dot in the lower right corner shows the indicator is working.
  • Every 2 weeks a bar automatically disappears. When only 1 bar remains make sure you have a new filter on hand.
  • After 2 months, when all bars have disappeared, an arrow will flash at the top of the display reminding you to change your filter.

Setting up Calendar Minder ® (Space Saver only)

The Calendar Minder ® is a simple dial calendar with the month and date to remind you when to replace your filter. Use it to make remembering easier.

  • Insert a new filter.
  • Set filter indicator to closest date 2 months from now.

On the date indicated, remove your filter and repeat steps 1 and 2.

Reading Your Indicator

Basic Brita® & Complete Chrome Faucet Filtration Systems:

  • Green: Your filter is working.
  • Half Red and Green: Replace filter soon. Your filter cartridge has two weeks or approximately 75 litres of life left.
  • Red: Your filter cartridge has reached the end of its life and needs to be replaced now.

Complete White Faucet Filtration System:

  • Flashing Green: Filter is working.
  • Flashing Amber: Replace filter soon.
  • Flashing Red: Replace filter now.

How to Clean a Brita Water Bottle

You feel good about switching from single-use plastic water bottles to reusable ones — you’re saving money and the environment at the same time. But if you noticed the water coming out of that eco-friendly water bottle doesn’t smell or taste so fresh, it’s time for a good scrubbing.

To keep your water bottle at its best, wash it every day. Here’s cleaning expert Leslie Reichert to tell you how to do it.

Daily maintenance

If you have a screw-top bottle, you’re in luck. All you have to do is separate the top from the bottle and run both pieces through the dishwasher every day (top rack only, of course). Make sure the drying cycle is on because the bottle needs to be completely dry. If not, it will become a breeding ground for germs.

Another option is to wash the bottle in warm water and detergent every day. Use a cloth or brush on the inside to remove any slimy build-up that may have formed. Rinse well and dry thoroughly before using.

Bottles with pull-up/push-down tops and those straw-type tops that you lift with your finger need a little extra attention during their soap and water bath. To clean those hard-to-reach nooks and crevices in the drinking spouts, use a small bottle brush. Rinse well and be sure to dry completely — either by air-drying overnight or hand-drying with a clean cloth.

How to Clean a Brita Water Bottle

How can I remove scratches from stainless steel?

To sanitize and freshen bottles

If, after regular cleaning, the bottle still doesn’t smell fresh, try sanitizing. Fill with either:

  • A mild bleach/water solution (1 teaspoon of bleach to 1 gallon of water); let the bleach solution stand for 5-15 minutes. Rinse until all bleach odor is gone. Air dry.
  • Straight white distilled vinegar; let it stand for about 10 minutes. Rinse and air dry.
  • Straight hydrogen peroxide; let it stand for about 10 minutes. Rinse and air dry.

Another method of sanitizing involves alternately spraying with hydrogen peroxide and vinegar. According Dr. Susanne Sumner, start by cleaning the bottle with soap and water. Then spray the bottle with either hydrogen peroxide or vinegar. (It doesn’t matter which you use first since each kills different strains of bacteria.) Allow spray to sit for 3-10 minutes, then wipe.

Follow the same procedure with the second one. Do not mix the two in the same bottle because the solutions together are unstable and will become ineffective. Rinse then air dry.

Most experts agree that most germs are removed by simply washing with soap and water or in the dishwasher. Sanitizing does not need to be done on a daily basis. However, if the bottle is shared among members of a group (as in childcare or school situations) or with a sick person, it doesn’t hurt to take extra precautions.

Using interviews with specialists, online reviews and personal experience, TODAY editors, writers and experts take care to recommend items we really like and hope you’ll enjoy! TODAY does have affiliate relationships with various online retailers. So, while every product is independently selected, if you buy something through our links, we may get a small share of the revenue.

This article was originally published March 3, 2016.

Your water bottle could be host to bacteria, buildup, and even mold. But with so many types of reusable water bottles available, it can be hard to know how to clean them. Follow our handy guide to learn how.

Is there anything as underrated as your water bottle? The handy item goes with you to the gym, your desk, the grocery store, and on daily dog walks. It might be in your favorite color or can keep ice water cold for hours on end. But the one thing your water bottle can’t do? Clean itself.

Experts say you really should wash your water bottle after every use. According to researchers at Treadmill Reviews, athletes’ water bottles, on average, host 313,499 colony-forming units (CFU) per square centimeter. For comparison, the average pet toy has just 2,937 CFU per square centimeter. That’s a lot of germs on your reusable water bottle! Plus, we know any warm, damp place is a breeding ground for mold growth. To make sure you’re drinking from a safe, clean vessel, check out our water bottle cleaning tips below.

3 Ways to Clean Water Bottles

Some water bottles are dishwasher safe. If so, toss yours in the dishwasher every time you run a cycle. However, even if the base of the bottle can go in the dishwasher, the lid might not. If your water bottle is not dishwasher-safe, use these common cleaning agents to get the job done.

Liquid Dish Soap

For everyday washes, warm, soapy water will do the trick. Fill the emptied water bottle with hot water and add a few drops of liquid dish detergent. Place the cap on your water bottle and give it a good shake—the water should begin to bubble inside. Dump out the suds, then use a bottle scrub brush to reach all the way down to the bottom of the bottle. And don’t forget to wash the exterior and bottom of the bottle as well. Once you’re done scrubbing, rinse your water bottle in warm water until you don’t see any soap bubbles and let dry thoroughly. Scrub the lid inside and out as well, paying extra attention to the spout opening or mouthpiece. Rinse and dry.

Distilled White Vinegar

Vinegar is our favorite go-to cleaning agent. Use it to clean your water bottle by filling it halfway with equal parts vinegar and water. Return the bottle’s lid and give it a few shakes before letting it sit with the solution overnight. The next day, be sure to rinse out the water bottle and the lid thoroughly with warm water to remove any leftover vinegar. Let dry. This is a particularly good way to clean a stainless-steel water bottle.

Baking Soda and Bleach

For hard-to-clean grime and mildew, consider cleaning your water bottle with bleach. Mix a teaspoon of bleach with a teaspoon of baking soda in your water bottle. Fill the remainder with water. Use the baking soda and bleach solution to scrub the cap as well, inside and out. Let your water bottle sit overnight, then rinse thoroughly with warm water in the morning. If your bottle is dishwasher friendly, we suggest running it through a cycle. Let dry.

How to Clean Water Bottle Lids and Types

New water bottles come with all the bells and whistles, including reusable straws, BPA-free materials, insulated double-wall interiors, and more. However, with these features comes special cleaning tips. Here’s how to clean specific types of water bottles when traditional cleaning techniques just won’t suffice.

How to Clean a Water Bottle with a Bite Valve

Water bottles that feature lids with built-in straws with a soft plastic bite valve are great for eliminating spills mid-workout. However, that handy feature can also harbor some serious germs and mold. According to CamelBak, you should clean a soft plastic bite valve by first removing it from the lid. Place the separate components of the bottle in the dishwasher and run it through a cycle. Use a cotton swab or straw brush to reach inside the valve with warm, soapy water. After cleaning, let dry thoroughly before reassembling.

How to Clean a Tumbler with a Straw

Most tumblers can be cleaned in the dishwasher or with the water bottle cleaning methods listed above. The reusable straws, however, need special care. We recommend purchasing a set of straw brushes. When you’re ready to clean your tumbler straw, rinse it with warm water, place a small amount of dish soap on your straw brush, and begin scrubbing the interior and exterior of the straw. If that’s not getting the job done, you can add baking soda to act as an abrasive.

How to Clean a Travel Mug

Travel mugs are typically used for hot drinks, but several water bottle companies use the same flip-top lid. If you plan to wash your travel mug in the dishwasher, be sure to use the top rack. However, if it’s insulated, you’ll want to hand-wash. Wash the lid by removing the rubber seal around the base and scrubbing with warm, soapy water. Be sure to get every nook and cranny of the lid because it can be a hot spot for mold.

How to Clean a Brita Water Bottle

Are you thinking about buying a Brita water bottle? Read this article before buying one.

A Brita water filter pitcher is quite a common sight in many a household refrigerator. Consumers enjoy the cleaner taste and better quality of the water, and it’s a much more environmentally friendly system than going through cases and cases of disposable water bottles.

According to Brita’s website, consumers use 2,000 plastic bottles every second, every day–yikes! However, one can’t deny that water bottles do come in handy during a workout, at the office, or on the go. The good news is that Brita is now officially manufacturing reusable Brita water bottle.

In this review, we’re going to take a look at Brita water bottle, as well as a few competitors. We’ll compare their specs and features and give you an honest analysis to help you decide whether or not a Brita water bottle is your top choice for portable hydration.

What Is a Brita Water Bottle?

How to Clean a Brita Water Bottle

As of June 2018, Brita has three basic water bottle designs: the Hard-Sided Bottle, the Sport Bottle and the Large Water Bottle. All three are BPA-free.

They each contain a replaceable Brita® bottle filter, which acts to lessen the smell and flavor of chlorine usually present in tap water and also filters out particulates 50 microns or larger in size. (For reference, a human hair on average has a cross-section of 50 microns.) The bottles also feature a built-in carrying loop for convenience.

There are a few benefits to using a Brita water bottle. The taste of your water is usually noticeably better.

In addition, the water you drink will be cleaner with the particulates filtered out of it. The other benefits are those that you reap with just about any reusable water bottle. You’re likely to save money because you’re not buying multiple disposable bottles throughout the year.

You’re also benefiting the environment by reducing plastic bottle waste. Just one Brita water filter can replace up to 300 of the standard 16.9-ounce water bottles that consumers have been used to buying for so long.

Brita Water Bottle Usage, Care and Maintenance

Brita water bottles are fairly easy to use and maintain, especially because they are dishwasher-safe. To clean the bottle, just take out the filter first, and place the plastic components on the top rack of the dishwasher or hand-wash them with mild soap.

When water is in the bottle, it’s best to keep the bottle out of direct sunlight to prevent algae growth. The most important thing is remembering to change your filter. For optimum performance, you should replace your Brita water bottle filter every two months or every 40 gallons.

Unlike some filters, the filter for Brita water bottles requires no “pre-soaking” period. To get started with the hard sided bottles, you’ll want to flush the filter for about 15 seconds under running water.

Then you place the filter into the filter housing in the lid and press down on it. You may have to push firmly to make sure the filter is flush with the straw. Once you’ve done that, line up the straw and lid and then rotate the straw to lock it. For the Sport Bottle, you start by pushing the filter into the housing, then filling the bottle up to the top with cold tap water.

Next, you make sure that the cap is securely tightened and then squeeze all the water out through the filter to activate it. This water and any water that you use to rinse a Brita filter can actually be used to water houseplants so that it doesn’t go to waste.

If for some reason any of the parts malfunction, Brita’s website offers a customer service phone number and claims that it “offer[s] a 30-day, unconditional, 100% money-back guarantee on all Brita® Pitchers, Faucet Filter Systems, Water Bottles and Filters.”

The water bottles are also under a 90-day limited warranty. When you are eventually ready to retire your bottle, you can actually recycle it (along with any old filters and filter packaging) through the Brita Recycling page on Brita’s website, as long as you have a least five pounds of Brita products to ship.

How to Clean a Brita Water Bottle

How to Clean a Brita Water Bottle

How to Clean a Brita Water Bottle

Many of us have made resolutions to travel more in 2020. If we manage to stick to this goal (unlike the ones to stay away from wine and chocolate that are most likely given up on by now), there’s a few things we’ll need. Yes, a cute passport holder or carry on bag are nice, but one thing that’s absolutely necessary before, during, and after your journey is water.

Sure, there’s water on airplanes but it’s known to be “conducive for microbial growth,” — so you probably want to have an alternative water source. Buying overpriced water bottles at the airport is an option, of course, but who wants waste money and plastic in this day and age? Consider water bottles that come with their own filters instead.

Beyond air travel, filtered water bottles are also ideal when traveling to destinations that lack plentiful clean water. Plus, they’re great to bring along on camping trips.

You may even consider using one for everyday use in your home as well. If you just don’t have room for that Brita in your fridge, why not have a portable one instead?

Whatever you choose to use it for, we’ve rounded up the best ones to make your decision-making a little easier.

Best for backpackers

How to Clean a Brita Water Bottle

1. LifeStraw Go Water Filter Bottles

“After using the Go Water Bottle on the trail for 3 hikes, I was in love. Simply put, the LifeStraw Go Water Bottle is easily one of the best hiking accessories I’ve ever used. It’s essentially a BPA free water bottle with a built-in water filter for a straw. You can literally scoop water from the stream into the bottle and drink it directly through the straw without waiting.”

Best for plastic haters

How to Clean a Brita Water Bottle

2. pH HYDRATE Glass Alkaline Water Bottle

“The packaging on this product is of high quality. Upon opening the top you are immediately greeted with the fragrance of the wood top. Quite a surprise. Water tastes great. Everything about this bottle is 100% high quality.”

Best for a serious world traveler

How to Clean a Brita Water Bottle

3. GRAYL Ultralight Water Purifier Bottle

“I was going to Cuba and thought about purchasing a water purifier in lieu of having to buy plastic bottles of water. I read a bunch of reviews and it seemed like the GRAYL was the best choice although it seemed expensive. Then a friend told me she had taken this to Africa and drank out of a river without getting sick! I immediately bought it. Another friend pointed out that the GRAYL would cost more than bottles of water for the whole trip which made sense but I have no regrets. I just feel good about not leaving behind a pile of plastic and at the same time drinking incredibly clean water that tastes great. I got the orange and I love it. Also, it fits perfectly in the side mesh pouches of a backpack.”

Change starts here. With us, with our kids, with the companies that initiate change. The choices we make impact our future and the future of others.

Stand Up For Clean Water launches today, #WorldWaterDay, with the new limited edition ME to WE Brita Statement Bottle. Every purchase of a Brita ME to WE reusable statement bottle or specially marked product during the month of March 2017, will provide a year’s supply of clean water to a person in Irkaat, Kenya. How cool is that?! EVEN BETTER is each bottle comes with a code so you can track where and how your bottle made an impact! Can you tell I’m excited about this?!

When I first heard about this campaign it moved me, like really moved me. And it moved my kids so much so they want to spend their own money (only $19.99) to buy one of these bottles to supply a year’s worth of clean water for one person. They understand the impact and importance of this campaign with very little explanation and being able to track their bottles makes this the real deal. Whether they use their own money or not we will be purchasing bottles for every member of our family.

Where to Buy:

You can purchase these bottles at: Wal-Mart, Real Canadian Superstore, Real Atlantic Superstore, Loblaws and Zehrs locations.

About the Bottle:

  • 700 ml portable bottle with replaceable water filter
  • BPA Free
  • Dishwasher safe
  • NSF certified to reduce Chlorine (taste and odour) and particulate (Class VI)
  • Just ONE Brita Bottle filter can replace up to 300 plastic water bottles
  • BPA free and dishwasher safe
  • Remember to change your filter every 151 litres or approximately every 2 months

Official Press Release:

Brita Canada is continuing their partnership with WE on a sustainable change initiative. WE is a movement that brings people together and gives them the tools to change the world. The campaign supports a borehole in Irkaat, Kenya that provides the community of more than 1,800 with access to clean water.

The program launched in September 2016 with Brita’s specially-marked filters and pitchers. This Spring, Brita will expand the limited edition packaging to include a statement bottle.

Every purchase of a Brita ME to WE statement bottle or specially marked product will provide a year’s supply of clean water to a person in Irkaat, Kenya. ME to WE creates socially conscious products and experiences that allow people to do good through their everyday choices.

As part of ME to WE’s transparent giving model, all ME to WE Brita products come with a Track Your Impact code for consumers to track exactly where and how their purchase has made an impact – consumers can go online and enter their unique code.

In addition to reducing contaminants that appear in tap water, Brita’s products save consumers more than $500 a year compared to buying bottle water, and help to reduce the volume of plastic bottles that end up in landfills or even worse, our oceans.

Take a stand, make a change in someone’s life, buy the bottle. When you do share on social media using these tags and hashtags! #BeTheDifference #WorldWaterDay

#worldwaterday
#Filterforgood
@wemovement
@BritaCA

I was compensated for this post. I fully support this initiative and campaign and all opinions remain my own.

Drinking lots of water during the day is good for you. And keeping a reusable bottle on you at all times is an excellent reminder that you should be drinking throughout the day. Saving the environment and doing something nice for your body? You go, Glen Coco.

But don’t pat yourself on the back just yet. If you’re like us, you probably haven’t cleaned your water bottle in. a while. And by a while we mean weeks. And by weeks we mean months. Hate to break it to you, but you really should be washing your water bottle every. single. day.

We know what you’re thinking: “But I only fill it with water!” It doesn’t matter, folks.

“Germs thrive in moist environments and spread easily when the conditions are right,” says Good Housekeeping Institute’s cleaning products director Carolyn E. Forté. “It’s not what you are filling it with but the fact that you are putting it to your mouth.”

Not washing your bottle won’t exactly create germs, adds Good Housekeeping Institute’s kitchen appliances director Sharon Franke. “But it gives germs a chance to grow.”

This applies whether you’re using a plastic, glass or metal bottles.

“Ideally, it is a good idea to clean your water bottle at the end of each day,” says Eric Hansen, the Director at Nalgene Outdoors. The ever-popular S’well Bottles also recommend daily cleaning, too. The same applies for glass bottles like bkr.

How to Clean a Brita Water Bottle

If you’re looking at your water bottle right now and trying to remember the last time you washed it, fear not. Just give it a thorough wash as soon as possible. You only have to toss your water bottle if it “appears to be degrading in some way―peeling, seal isn’t tight, rusting, melting, etc,” says Franke.

Oh, and just so we’re clear. Cleaning your water bottle doesn’t mean just rinsing it with. more water. “You’ll want to use soap and hot water to get rid of germs,” Forté says. “And pay special attention to the nooks and crannies in the cap. Germs have been found in these caps even after washing if they aren’t washed thoroughly enough.” Awesome.

How to Clean a Brita Water Bottle

When it comes to cleaning your trusty water bottle, PopSugar has a few suggestions.

First and foremost, you can clean it simply with soap and warm water as Forté suggested. Alternatively ― depending on the brand of bottle you have ― you can put your bottle in the dish washer. Just make sure it won’t get ruined in the process.

Or, you can DIY the situation by using vinegar’s natural disinfectant qualities to clean your bottle. Just fill half of your bottle up with white vinegar, fill up the other half with water, let it sit over night, and thoroughly rinse in the morning.

Last Updated: March 22, 2020

How To Clean Water Bottles.

This article will tell you everything you need to know about how to clean water bottles. Once cleaned properly your bottle will be long-lasting, and most importantly mould-free!

Water bottles are a fabulous idea. Buying a very nice bottle that you like looking at and like even more to drink from is a great way to keep yourself hydrated. Especially when you’re out and about and perhaps don’t trust the local water supplies. Or worse, don’t have access to water at all. Although there are inherent problems with water bottles especially plastic ones, it is still better to have it than not.How to Clean a Brita Water Bottle

We all like to put funky things in our bottles from time to time to make the water more interesting. For instance, sticky sweet sports drinks, slices of fruit, purification tablets and plain old water itself.

However all of these things can turn your water bottle into a potential breeding ground for mould and bacteria.

If this is something that worries you (and let’s face it is otherwise you wouldn’t be reading this). Check below for fail proof tips to keep your water bottle clean, long-lasting, mould free for many years to come.

How To Clean Plastic Water Bottles

1. Wash By Hand

In most cases, a good and thorough rinse by hand with soap and warm water is a good way to clean most bottles. If you have time, leave the warm water and soap solution in the water for a few minutes before rinsing it out. This means that a) the soap keeps on doing its job long after your tired and b) it will get rid of any weird smells in the bottle. Just make sure you rinse it out thoroughly so as to be sure that you don’t also end up drinking some of the soap in your water. Any general, all-purpose liquid washing up soap will do the job. How to Clean a Brita Water Bottle

2. Clean The Water Bottle Cap

This is an easy thing to do as we are most likely to be focused on cleaning the bottle and may just give the cap a cautionary rinse. But remember that if the cap is not properly cleaned then it will only contaminate the rest of the bottle anyway. Also, caps that are taken off will usually be placed somewhere like on top of a table where it might pick up germs and bacteria. So be sure to give the cap as much attention (if not more) when washing the bottle. Squeeze soap and water through the nozzle if your hand or brush can not easily get to it.

3. Use a Brush To Clean Water Bottles

Periodically, it is a good idea to wash the bottle with a brush because your hand can only do so much. You don’t need anything fancy a simple brush that has a long handle is sufficient. You can get these at almost any department store or even a larger supermarket. When using this make sure to scrub harder if the bottle contains some sticky residue or mild stains.

4. Don’t Put Your Water Bottle in The Dishwasher

Yes, it is tempting to just throw your bottle into the dishwasher and let it do all the work for you. But did you know that the temperatures in most dishwashers are close to boiling? If your water bottle is plastic then this might deform it and also degrade your bottle over time. Also, the dishwasher will not be able to clean it internally like you would with a brush or even your hands.

How to Clean a Brita Water Bottle

5. Clean After Every Use

You would always wash a cup after each use right? Think of the water bottle in the same light. Once you have finished with its contents, don’t just refill but wash the bottle every time. Just as you would for a drinking glass, wash your bottle every time. This applies even if you have only used it to drink water or at the very least, rinse out the used bottle.

6. Do Not Use Harsh Cleaners

It’s not a good sign if you feel that you have no option but to use something as strong as bleach or another type of harsh cleaner. If you need something like this to properly clean your bottle then it’s probably time to throw the bottle away and buy a new one. You should avoid putting something like bleach into your bottle. This is because unless you rinse it out enough then it could end up contaminating your bottle. The last thing you ever want to drink is bleach.

7. Know When to Throw The Water Bottle Away

Finally, when it comes to “How To Clean Water Bottles” this might be the most important point of them all. No matter how well you maintain your bottle there comes a time when all bottles should be recycled and go on to a better place. It is almost impossible to keep it bacteria and mould free forever and plastics usually degrade over time. Always inspect your bottle for scratches, mould, where the plastic has become soft. Some times there is a smell that just won’t go away. This is no matter how much you wash the bottle. If this is true for you, then it’s time for a new bottle.

ABOUT THE AUTHOR

Pam Murphy

Several Brita water filtration models have earned gold seal certification from the Water Quality Association for both contaminant reduction and aesthetic quality of filtered water. The Water Quality Association website lists each qualifying model, noting which contaminants were reduced in health effects testing and addressing taste and odor quality in aesthetic testing.

Identification

Water filters, including the Brita brand, are designed to improve water quality and taste, as well as to remove impurities from the water. Not all water filters are certified to remove every type of contaminant. Some models are more effective at filtering lead than others, for example. Check the packaging label to identify the filtering claims associated with a particular model.

Types

Brita markets several types of water filters. Depending on your preferences and the amount of water you need to filter on a daily basis, you can choose to purchase a faucet filtration system, a pitcher with a replaceable filter or a refrigerator filter. Undersink models are also available, but are often more costly than other types.

Considerations

Consumer Reports recommends that you find out what types of contaminants your water contains before choosing a water filter. If your main concern is taste, some models are designed specifically to improve taste. However, if contaminants are a concern, you need to choose a model that meets your needs. The Environmental Protection Agency explains that local health departments are often equipped to test well water free of charge. If you use a public water system, contact your supplier to inquire about water testing results. The EPA also provides an online listing of certified water testing labs by state.

Effectiveness

Lead is a primary concern in drinking water, according to the Lead Education and Abatement Design Group. Dr. Brian Gulson, chief research scientist for Australia’s Commonwealth Scientific and Industrial Research Organization, tested the effectiveness of Brita’s jug system and found that the product consistently filtered 80 percent or more of both lead and copper. The Brita filter purified the water so that it met regulatory guidelines, according to Lead.org. Consumer Reports also notes that the Brita Smart Pitcher resists clogging, although it isn’t certified to remove organics.

Upkeep

Replacing water filters regularly ensures that you get the best possible performance from your filtration system, according to Consumer Reports. If you fail to change out the filter, contaminants trapped in the old filter could get dumped back into your water. Follow replacement recommendations on your Brita filter packaging to make sure you get the most from your filter system.

How to Clean a Brita Water Bottle

Last Updated on April 7, 2020

Coming from Arkansas, the idea of filtering water had never crossed my mind. Arkansas has pure, spring fed mineral water.

How to Clean a Brita Water Bottle

It’s some of the best tasting water in the world. If you live in Arkansas and buy bottled water, I could slap you. When I left Arkansas to embark on my acting journey, I brought along with me my trusty bobble.

It’s a water bottle that filters the water as you drink. It’s plastic but was a lifesaver in Pennsylvania, Maryland, and Florida. Florida has to have some of the nastiest water in the US. And, while California isn’t the worst… it’s no Arkansas.

The water is very, very hard here. It has caused a litany of skin problems. My hair isn’t fluffy, my skin is dry, and I’m more prone to breakouts. You want to know why women in the south have big hair? Besides teasing, it’s literally in the water.

How to Clean a Brita Water Bottle

After almost two years, I’m finally finding a new system to help with these issues. I was starting to get used to drinking our tap too, but Justin was very insistent on filtered water.

We’re both well aware that bottled water is no safer than tap water; plus it’s an exorbitant waste of money. I don’t want my drinking water surrounded by plastic whether it’s single-use or more permanent. Bottled water and Brita pitchers were both out.

Brita pitchers, fridge filters, most all water filters use activated charcoal to filter water. I’m sure this name rings a bell… it’s been used in my eyeliner and face mask recipe.

How to Clean a Brita Water Bottle

I stumbled into the world of activated charcoal when trying to make eyeliner and mascara. I watched this great video tutorial, but making it from scratch seems difficult and time-consuming. I am so grateful Rainbow has it in bulk!

Instead of using activated charcoal particles, I just use an entire activated charcoal stick. It works the same as every other filter just in a different form.

how does it work?

Place the activated charcoal stick in a glass carafe full of tap water and let it sit for several hours. Don’t use a plastic jug; it really needs to be glass or stainless. I use an upcycled glass milk bottle.

Activated charcoal naturally bonds with toxins. The sticks remove mercury, chlorine, copper, and even lead. It does not remove fluoride. So, don’t worry! I am getting plenty of fluoride without having it in my toothpaste.

How to Clean a Brita Water Bottle

how long does it last?

They last around 4 months. They do take a little bit of maintenance. Every 3-4 weeks the surface will fill up with toxins. You need to release the toxins so it will keep working. It’s very simple. Just boil the stick for 10-15 minutes, discard the water, and it’s ready to use!

what happens after four months?

Compost it or use it as a deodorizer. I keep one under Nala’s kennel. You could keep one in the fridge, by your shoes, or any other place you need to help control odor.

There are several options out there, but I like this one and this because their packaging is compostable.

There is nothing wrong with Brita pitchers. It is still wayyyyyy less waste in the long run than buying bottled water. But, once your Brita pitcher is no longer in working condition, consider switching to this eco-friendly option. Plus, it will save you a lot of money! Brita refills aren’t cheap.

How do you filter your water? Would you give a charcoal stick a try?

This post may contain affiliate linking you can read more on my disclosure page.

In need of fresh-tasting water away from home? Check out the Brita Filtering Bottle solution!

*This post is sponsored by Brita but the content and opinions expressed here are my own.

**There are some affiliate links below, but these are all products I highly recommend. I will never put anything on this website that I haven’t verified and/or personally used. I may receive a small commission in exchange if you purchase through my links, that is at no additional cost to you. Please see my Privacy Policy + Disclosure for more information.**

How to Clean a Brita Water Bottle

There are many convenient ways to get great tasting filtered water at home, but what about when you are away from home? Where do you go to get clean, filtered drinking water? Most of us probably carry around one of those disposable plastic bottles of water, but we know the problems those bottles have become. Well, I’m here to share with you a better way to get clean, great-tasting, filtered water on-the-go through reusable Brita Filtering Bottles!

About the Brita Filtering Bottle

Brita Filtering Bottle is a 26-ounce reusable plastic bottle with a filter built-in. It has a fixed carrying loop, so it’s easy to hold as you walk around. It comes in six different colors, or you can get it in stainless steel. The bottle is dishwasher-safe (top rack only) and is BPA free. The enclosed easy-sip straw can be used upright. When you purchase, it comes with one replaceable filter which needs to be changed every two months. It has a leak-proof lid, so you don’t have to worry about it spilling at your office desk or during that important meeting at work.

How to Clean a Brita Water Bottle

What Does It Filter?

This Brita Filtering Bottle cuts down the taste and smell of chlorine. It also filters impurities like particulates (Class VI) found in tap water, giving it a better taste.

How to Clean a Brita Water Bottle

Why Use?

It is so convenient to take this reusable Brita Filtering Bottle anywhere! How many times have you been at the airport and purchase a water bottle that nearly costs $5 for a 16.9-ounce bottle? With a one-time investment of less than $20, you’ll be able to get rid of the single-use water bottle (talk about saving money in the long run)! Just make sure it’s empty when you go through security, and you can fill it up once you get through TSA.

How to Clean a Brita Water Bottle

Use anywhere – work, school, travel, gym – it’s so convenient to take it on the go! I know for sure I’ll be using it frequently at the gym, as I hydrate from my cardio boxing class and weight training.

How to Clean a Brita Water Bottle

It’s also a great feeling to reduce plastic waste. According to Brita, one filter can replace 300 plastic water bottles (standard 16.9 oz bottles), meaning you’ll be replacing up to 1,800 plastic water bottles a year! It’s nice to have an option that provides a convenient way to get filtered water wherever you are and help the environment at the same time.

Purchase a Brita Filtering Bottle today and let’s make the planet more sustainable!

Getting clean water is easy, right? Of course, it is! That is because there are so many filters out there that anyone can find one that’s virtually perfect for their needs. However, you should learn about maintenance, namely how to clean a water filter cartridge as it is an essential step towards keeping the water safe to drink.

The product’s manufacturer usually gives guidelines on how and when one should clean a filter or filter cartridge casing. While one might be familiar with how to clean a water filter, cleaning the cartridge case involves some extra steps.

Generally, cartridges are found in prefilters, which are devices placed strategically to filter the water before it reaches the tap. Hence, let’s talk a bit about prefilters before we discuss what the general consensus on the best ways to clean these items is.

What are Prefilters?

Take the classic water filter. It’s usually used in treating water for odor and taste. It might come in the form of a countertop filter, a tap filter or a water pitcher. They’re all great devices, and anyone should own at least one of them to ensure a clean and great-tasting water supply, but they’re usually inefficient in treating water hardness.

What is water hardness? How can a fluid be hard? Well, hard water is water that has high mineral content, and it will usually appear white and murky, but it will taste the same as any other type of water.

This occurs because the water supply comes from an underground source rich in limestone and other types of contaminants. While these aren’t the most harmful contaminants, the minerals can accumulate and do damage to the pipes or the body.

In fact, conditions such as kidney stones are believed to be caused by drinking hard water on a daily basis. While they’re hardly life-threatening, they can sure cause some pain and damage in their way.

So, that being said, what is a prefilter? The prefilter is usually installed somewhere along the plumbing, like under the sink. It consists of a tubular filter cartridge that’s protected by a housing. In this case, the filter will oftentimes be a porous material and will trap the particles found in hard water before they reach the user.

How to Clean a Brita Water Bottle

How to Clean a Water Filter Cartridge Casing?

First off, forget everything about cleaning products. Filter cartridges and masks are very frail, which means that any sort of concentrated cleaning product will damage them irreversibly.

With that in mind, let’s get to the practical steps on how to clean a water filter cartridge casing.

  1. Determine where the filter or pre-filter has been installed

Softeners, for instance, can be installed anywhere along the plumbing. It’s common for people to bypass the cold water supply (to avoid an increase of sodium in the drinking water) and install them for just the shower or the kitchen sink. They’re usually of a tubular shape, with one or two elements.

  1. Cut its Water Supply

Water filter systems usually have a dedicated valve that allows users to direct the filtered water to a designated appliance or part of the household. So, the second step would be to turn off the water supply that runs through the filtration system. Afterward, go to the corresponding tap and drain out all of the remaining pressure from the system.

  1. Expose the Cartridge

Find the filter and use a wrench (or your hands) to remove the outer casing gently. Depending on how often this process takes place, the user might opt to keep or replace the rubber gasket that seals the mask. It’s usually recommended to replace the gasket around once or twice each year (twice to be extra safe).

  1. Remove the Cartridge

Now, here’s where things get tricky. Cartridges shouldn’t be cleaned; they’re one-time products that need to be swapped with reserves in order to keep a clean water supply. Whether it’s a sediment filter or a charcoal filter, there isn’t really much difference. The number of contaminants that builds up in the fabric will definitely render it useless.

  1. Scrub the Mask Clean with Lukewarm Water

Scrub the outer casing with a mild detergent and lukewarm water. Use a soft brush in the process as damaging the casing might result in a faulty or leaking system, something that can become a real pain.

How to Clean a Brita Water Bottle

  1. Make Sure to Run Water Through It

After scrubbing and rinsing, allow water to pass through the casing for a couple of minutes. Better yet, let it sit for half an hour and run some water through it again. It’s a great way of ensuring that the casing has been properly cleaned and that everything goes back into place, preventing leaks and other issues.

  1. Install the New Cartridge

Open the casing and place the new cartridge in it. Again, allow some cold water to pass through to ensure that everything fits in place. At this point, the system should be fully operational and ready to work.

How to Clean Pitcher and Tap Water Filters

Pitcher and tap water filters require maintenance too. Apart from changing the filter, they require a good scrub before putting back together. It’s recommended to change a filter once every three months, so it’s easy to get used to it and perfect the technique.

  1. Disassemble the pitcher or tap water filter.
  2. After doing so, separate the filter from the rest of the system.
  3. Place the pitcher or tap water filter in a mixture of lukewarm water and white vinegar.
  4. If they sit in the mixture for around 10-15 minutes, most (if not all) impurities should dissolve and disappear with nothing more than a quick rinse.
  5. If impurities are persistent and latch onto certain places of the filtering system, then use a Q-tip or a soft brush, along with a mild soap, to scrub down and dissolve any remaining goop.
  6. Replace the filter and put everything back together and give it a try.

Final Thoughts

It’s really easy to perform maintenance on these simple (but very efficient) products. Most of the time, the user will only require household items and time. In addition to keeping the drinking water crystal-clear, performing regular maintenance will increase the lifespan of the filtering system.

Last update on 2020-08-26 / Affiliate links / Images from Amazon Product Advertising API

The question we often get goes something like this: “What do Brita Filters actually do?” or “What does Brita not filter out?” or “Are Brita products safe to use?”

When assessing whether or not Brita filters are safe, the tough answer to these questions are that No, Brita does not remove enough contaminants to be considered safe to use by our standards. These so called “Filters” are doing consumers a huge disservice by not providing water that is truly clean & safe to drink. Another easy way to put it is, “not all filters are the same.”

But how can this be? One might ask. Brita is after all, sold in major retailers like Target and Bed Bath & Beyond. How could they not be filtering out the bad stuff?

MUST READ: Brita vs. Clearly Filtered – Comparing the Two Filters

It’s a very legitimate question and one we’re thankful consumers are starting to ask. While Brita is in the industry of water filtration just as the ClearlyFiltered products are, the similarities seem to stop there. The difference really is the technology within the filter.

You see, Brita’s products use a very simple, cost-effective carbon filter which they claim makes tap water “taste better” by “reducing” chlorine and not much else. You have to ask yourself, how much “Filtration technology” can they cram into a filter that is 4 for $9.99? Their filters must cost them mere pennies to make. And that means you sacrifice which contaminants you are willing to put up with all because of the economies of what you are willing to pay. If you buy a cheap filter, you are getting a cheap filter.

Is a Brita water filter safe? The more important question is: how much is the health of you and your family really worth to you?

The problem with words like “filter,” “reduce” and “taste better” is they are intentionally vague, hence why companies like Brita use them to describe their products. They don’t mean much of anything but they sound really good. To illustrate my point: pouring water through a paper towel will “filter” it, but that doesn’t mean it’s been properly treated and ready to drink by any standard I’m aware of.

This is where our ClearlyFiltered products really stand out. Our filters are actually classified as water purification products which means they adhere to a much higher standard for water quality set by the EPA.

You can see in the chart below some of the main differences between ClearlyFiltered and the other leading brands.

So whether you currently have a Brita pitcher, are buying replacement filters or are simply looking at the different options on the market we encourage you not to overlook the claims of each product very carefully. Sometimes it’s hard to tell the difference from actual claims and marketing spin. And as always, if you have any questions we’re just a click away!

Amy asked: I cleaned out a reusable water bottle with soap. Now, I can’t get the taste of soap out. Any suggestions? I have rinsed it with water many, many times. I’m afraid to put lemon juice or vinegar into it because I’m afraid I won’t be able to get those out as well.

Reusable How to Clean a Brita Water Bottlewater bottles are made from plastic, which is porous and can absorb its contents and seem to hold onto them for a long time. In this case, the plastic has absorbed some of the soap and it slowly releases when it is filled with water. The first step is to neutralize the soap/detergent and rinse it quickly to get rid of the soapy taste. Then, in the future, avoid letting any soaps or cleaning solutions sit in the water bottle for any length of time. By giving it a quick wash, rinse and allowing it dry thoroughly after each use, the water bottle will stay clean, mold free and ready to offer a fresh drink each time.

You Will Need:

  • Bleach
  • Hot water
  • Drying rack
  • Spray bottle (optional)

Steps to Remove the Soapy Taste:

  1. Start by washing the bottle and rinsing immediately.
  2. Place a small amount of bleach in the bottle and fill with hot water. It is often convenient to keep a spray bottle filled with bleach under the sink for quick clean-ups.
  3. Place the lid on the bottle and shake it for 15 seconds.
  4. Dump out the contents and rinse thoroughly.
  5. Place the bottle upside down on a drying rack and allow it to dry completely.

They are BPA-free, reusable and can be refilled with tap water. Reduces chlorine for great-tasting water. Ounce Hard Sided Water Bottle with Filt.

Buy with confidence as the . FREE DELIVERY possible on eligible purchases. The filter inside this BPA free bottle .

How to Clean a Brita Water Bottle

This portable water filtration system helps filter out and reduce chlorine taste and. Thought this would be great especially for air travel. Find your favourite groceries, independent producers, and our Low Price Promise at ocado. The best water bottle has on-the-go filtration and helps reduce plastic waste from bottled water. What information would be useful here?

LinkCircumference of the Earth. Shop BRITA Water Bottle Filtration System – compare prices, read reviews, add to shopping list, get product info, or find in store. Many products available to buy .

The new water filter bottle from BRITA filters your water while you drink. BRITA products include water jugs, kettles and tap attachments, all of which. This article explores the pros and cons of each. They would definitely be easier to pack.

Brita : Filters for Good. Canada day water bottle with replaceable filter to make tap water taste great anywhere! All plastic components ( bottle , cap, straw and mouthpiece) can . The bottle can be filled with tap water and the . Your kids can enjoy cleaner, filtered tap water. Suppliers must provide data on electrical and fuel use, water input and output,. And what about what goes into the bottle ? TripAdvisor among attractions in Sunrise.

The BPA-free filter reduces chlorine taste, odor and particulates often . Every day the kids are allowed to have an endless supply of water , one. The lid can break into pieces with sharp points, posing a . This BPA-free, reusable water filter bottle with easy-sip straw, durable plastic body, and replaceable filter reduces chlorine taste often found in tap water. Fitted with the BRITA MicroDisc, the lid itself filters out taste impairing substances. Filters ordinary tap water as you drink and reduces chlorine .

To lead a healthy lifestyle, people do things that help them to stay safe and fit. And to do so, they look for the easiest ways. That’s why I guess water filtering pitchers are so common. Yet the filters of the water pitcher do not last long. Replacement filters are readily available at supermarkets, pharmacies, and suppliers of retail sales.

Brita filters can remove pollutants and harmful substances from regular tap-water. It contains activated carbon that removes the chlorine and improves the taste and smell present in tap water. Filtration systems for Brita pitcher and faucet need specialized filters.

You need to replace that time to time, and for that, you need to know how to change Brita filter? Here we are to help you.

How Frequently Do You Need to Change the Brita Water Filter?

We don’t like to start a conversation in such a specific way about how often to change a Brita filter. That’s not as simple as just the quantity of gallons or the amount of time. It varies with the quality of water treated and the amount of water used.

How to Clean a Brita Water Bottle

If you need your filter to continue removing contaminants from your water, you also need to remove it so often. Without it, the water flow rate of the water filter system will slow it down. It will result in an inadequately functioning or not functioning at all.

Brita claims that after using 40 gallons of water, the regular filter needs replacement.

As Brita has a few containers of different sizes, we suggest you find out how much water you use every day to determine how often to change Brita filter.

We suggest calculating filter replacements by days to weeks instead of container fill-ups. So, if anyone has a habit of filling the container and does not check, you might end up using the filter for a longer time than you need to do.

Pay heed to your filtered water after using a filter for 1 week. Then you can be able to identify very quickly how long 40 gallons of filtered water can be used. Thus you can determine how often to change Brita water filter.

How to Know When to Change Brita Filter

Brita filters have indicator lights that help you to determine it. A yellow light means that soon the filter needs replacement. While the blinking red light means an immediate replacement of the filter. As mentioned above, after the use of 40 gallons, filter efficiency drops. Replacing your filter on a regular basis ensures healthier and excellent water.

How to Clean a Brita Water Bottle

As water quality varies for every household, there are other ways than a visual indication to identify that your filter is dirty and needs replacement. When you sense an odor in the water, or it carries an odd taste, it is most likely the time for removing your water filter. A noticeable reduction in water pressure can also occur, indicating the need for a new one. Please check the water use requirements of the supplier to ensure that you have not failed to meet them.

Brita Pitcher Filter Replaces Step by Step

After knowing how often to change Brita pitcher filter, we will guide you some steps to follow to change Brita filter.

The Brita filter cartridges need pre-soaking before installation. So, pre-soak the filter in fresh cool water as indicated on the filter package if you use the original model filters.

Make sure the replacement of Brita filter after every 40 gallons of use as directed by Brita.

How to Clean a Brita Water Bottle

Begin with thoroughly wash your hands and keep a couple of clean paper towels.

Use mild dish-washing soap to clean your Brita filter pitcher or other container and put it on a clean paper towel.

Fill a bucket with sufficient cold water to dip the Brita filter entirely in the water. Then take out the filter carefully from its box and put it for 15 seconds in the bowl of water to soak.

Lift the new filter from the soapy water and leave it for a couple of seconds to drip water. Now, line up the filter to the housing of the filter. It will join the groove along with the filter inside the housing of the filter.

Holding the filter straight in alignment with the housing, insert the filter cartridge and gently press to fit. If you don’t think the filter is not placed correctly, remove it and re-insert to ensure it the correct placement.

The filter has carbon which can produce some carbon dust. This carbon dust will make very blurry water in the first few pitchers. Avoid drinking and throw away or use that water for other purposes like using plants or household cleaning.

Why You Need to Change Brita Filter

Since you are aware of how to change Brita filter cartridge, here we have some more knowledge to share with you.

The filter will last longer if you use to filter the water that requires minimal filtration than the water that is highly contaminated. Is the concept real? Let’s learn about it.

A Brita filter cartridge has activated carbon to remove some water pollutants to give better taste and smell in the water.

The more this activated carbon is used, the more it loses its capacity to eliminate contaminants. So, the water used in the filter is full of pollutants or not; the activated carbon in a Brita filter will, at some stage, lose its effectiveness.

The main thing to take away from all this is that a filter from Brita that can eliminate high levels of pollutants may not last long.

Activated Carbon & How Brita Filters Work

If you have the experience to use Brita Filter, you may have seen some black specks inside the dispenser.

Black speck is known as activated charcoal, the principal filtration component of Brita Filter.

How to Clean a Brita Water Bottle

Charcoal stick impurities and passes water to make it clean from the undesired items. After sometimes impurities start to make up and make the filter less effective

If you like to get similar attributes with cheaper replacement, we need few activated carbons.

You may order some activated carbon on online; it saves a lot of money for you.

The function of Brita Filter is to remove chemicals or contaminants from normal tap water.

In Brita Filter, there is activated carbon that removes odor and taste of chlorine found in tap water.

Brita faucet or pitcher needs unique filters. In pharmacies, general merchandise retailers and the grocery shops you can get replacement filters.

It’s my favorite season: iced coffee season. Well, technically, summer is my least favorite season—but iced coffee season is a season of the mind. Everything is better during iced coffee season. Except the smell wafting from my metal drinking bottle.

To make iced coffee, I favor a wide-mouthed S’well bottle, because I am super basic, but also because I found the opening is wide enough that I can easily fill it with ice and perch my pour-over brewing device atop it to make a quick Japanese iced coffee . Unfortunately, my bottle—made to hold water—loves to absorb the scent and flavor of the brew, which makes it less than ideal when I fill it with. basically any other liquid. Luckily, I’ve discovered a few different methods to deodorize it, ranging from the simple to the more intense.

How to Make Japanese-Style Iced Coffee

Nothing livens up a hot afternoon quite like a cup of iced coffee. Trouble is, a lot of the iced…

Soap and a bottle brush

The dishwasher is right out—HAND WASH ONLY, the bottom of the bottle warns me—but as long as I haven’t let coffee linger for a few days, I can usually get things smelling all right again by giving it a scrub with a bottle brush and some dish soap. I already had a bottle brush lying around because I have small children who like to drink out of weird and hard-to-clean plastic cups, but if you don’t, they aren’t a bad buy—you can also use them for cleaning wine glasses, highball glasses and anything else you drink out of but can’t fit your hand down into.

Boiling water

I can’t always get the water from my kitchen faucet hot enough to clean things effectively, so I’ll use my goose-necked kettle (the same one that helps me craft the aforementioned iced pour-overs) to add a bit of boiling water to any persistently grimy pots or pans. The same method can help get clingy smells out of a metal water bottle, and since the things are made to keep liquids hot as well as cold, you can pour the boiling water in, close the lid, and let them soak for as long as necessary for the heat to do its work—overnight if the timing works out, but a few hours will usually do the trick. Plop in a few drops of dish soap at the same time to boost your cleaning power.

How to Clean a Brita Water Bottle

Vinegar soak

If boiling water doesn’t do it for you, another option is to do an overnight soak with a mixture of white vinegar and hot water. Rin se the bottle, fill it about a quarter of the way with white vinegar and top it off with hot water (from the tap is fine, but go for boiling for some extra edge). Secure the lid, give the bottle a shake and let it sit overnight. Rin se well before using it the next day. The vinegar smell shouldn’t linger, and and sour coffee odors should be gone.

Baking Soda and Vinegar Are Not the Sink-Saving Combo You’ve Been Led to Believe

While it’s great to opt for natural home-cleaning solutions whenever possible, they’re not always…

Baking soda and bleach

My preferred option—because I usually can’t find the white vinegar—is a combination of baking soda and chlorine bleach . If it seems weird to pour bleach into something you’re going to drink out of, I get it, but you only want to use a tiny bit—you want to mix 1/2 teaspoon of bleach and a heaping teaspoon of baking soda in a bowl of water large enough to submerge your water bottle in it, per this earlier Lifehacker story . The benefit to this method is that you can soak the bottle’s lid as well—it’s a good way to clean up inside the ridges and rubber seals—but you’ll want to rin se, rin se and rinse again when you’re done, because you don’t want to drink bleach. ( Or do you? No, you don’t. ) If the idea of adding bleach to your water bottle is a step too far, you can also omit it, double the amount of baking soda, and soak overnight.

Denture tablets

In this Lifehacker post from 2014 , Alan Henry recommends cleaning and sanitizing your reusable water bottle with a denture tablet. I wouldn’t buy them just to try this out myself (baking soda is a lot cheaper, for one thing), but if your local senior citizen has a cache lying around, give it a whirl.

How to Clean a Brita Water Bottle

This post is part of a social shopper marketing insight campaign with Pollinate Media Group™ and Brita, but all my opinions are my own. #pmedia #BritaOnTheGo http://my-disclosur.es/OBsstV

How to Clean a Brita Water Bottle

This past week has been both busy and enjoyable. It seems that the nicer is gets outside, the more I have to get done. Our day to day lives can get so busy that sometimes we can forget to take some time to take care of ourselves. It’s important to take care of the little things and stay hydrated when we get busy.

It’s heating up outside and I cannot seem to get enough of the outdoors this time of year. It feels great to put on my shoes and hit the walking paths and hiking trails in the area. Being outside is refreshing and rewarding. I have a lot of projects I need to get done for the house such as planting a vegetable garden and painting the deck. I’ve also scheduled some me time and so it’s the best of both worlds. From the time I wake up in the morning until I lay my head down at night, I’m on the go.

I stay pretty busy throughout week and can’t afford to get dehydrated. If you’ve ever been dehydrated then you know that it’s no fun. Not having enough water can lead to headaches, muscle aches, a foggy brain and a sluggish body. I always, always have water with me wherever I go. From the time I wake up in the morning to the evening, I’m drinking water. Drinking more water can boost the immune system, aid in losing weight and lead to better sleep. I’ve found that by having a filtered reusable water bottle, I drink more water. It’s convenient to be able to fill it up anywhere. The water is truly crisp, cold and refreshing. I got this Brita Water Bottle from Walmart in the hardware section. They have a large selection of these reusable bottles that are both hard shell and soft.

On Saturday, I spent time working on the garden. Planting new flowers, adding soil, hay and trimming the trees. Temperatures reached 90°F later in the afternoon and so I made sure to get it all done earlier in the day.

After a busy work week that consists of making recipes for the website, styling food and taking pictures, editing photos and writing content and keeping up with social media, it’s nice to take some me time. My weekends are spent outside doing something fun. This week I wanted to get outside to plant some flowers I had sitting around for the past few weeks. I find gardening to be a great stress relief. It puts me at ease is can be very rewarding. I love going outside to take a break in summer to water the garden. It gets very hot and humid in the south during summer month. In fact, 9 months out of the year it’s hot here and summertime can be unbearable if you’ve never experienced it and therefore I never leave the house without my Brita Water Bottle.

How to Clean a Brita Water Bottle

Once or twice a week I take a photography class. Some days we are in a house learning and other days we are all over the city photographing life.

How to Clean a Brita Water Bottle

Even though I don’t travel far, heavy traffic means I’m sitting in my car a lot. It’s nice to have a reusable water bottle with me.

How to Clean a Brita Water Bottle

After work, I come home and usually put dinner in the oven. Then, I clean up the house a little before heading outside to take a quiet walk along Lake Pontchartrain. I take a few pictures of nature on my walk.

The summer sunsets in the south are amazing on the lake. I’ll stop by the park where kids are playing baseball on the way home and refill my Brita Water Bottle with tap water before heading home.

I use Brita because it makes the water I drink taste better. Having this filter simply means it’s removing zinc, cadmium, chlorine, copper and mercury. By removing these harmful contaminants, it’s one less thing I have to worry about. It also leads to me drinking more water and staying hydrated.

How to Clean a Brita Water Bottle

Here are a few tips to increase water intake.

1. Replace sugary beverages with cold water.

2. Buy a reusable Brita Water Bottle. Fill it up at the office, school, outdoor parks, bathrooms or anywhere a blubber or sink is.

3. Add fresh fruit to water. Simply add a lemon, lime or cucumber slice to water.

4. Drinking water when you first wake up in the morning can flush out impurities and will jump start the metabolism after sleeping all night.

5. Drink water with every meal and snack during the day.

6. Freeze little bits of peeled lemon, limes, oranges or cucumber and use them in place of ice cubes.

Using a reusable water bottle costs less than buying water bottles.

For more information and uses of Brita Water Bottle, check out their Facebook and Instagram pages.

Brita Sports Water Bottle Review

I find myself a filtered water fan rather than bottled spring water, or even purified water. If you agree with me, you may want to invest yourself a Brita Sports water bottle. Be warned though that this bottle is not nearly as fun, or customized as the Bobble, which will be reviewed later. That being said, lets enter this review without any bias.

Upon opening the package, which contains initial instructions, and a pamphlet containing coupons and other product advertisements, I noticed that the bottle was already assembled, the filter was already snapped in, and required no setup. The instructions tell you to rinse it out once so the excess carbon can be washed out. One you do that, you into shape to get going! Now, to go to the aesthetic values of the bottle, its nice an simple. With the Brita logo at the lower area of the bottle, and the solid color (my bottle is blue), its a rather humble design. No outstanding curves or bright colors, which is nice, but from a sports bottle, I would have expected a little more of a bright color. Nonetheless, the water tasted great, just like water from a good filter. The plastic is a little weak however, and I was able to accidentally scratch it while refilling it, but should last a few months with normal use.

Overall, we would rate this bottle a 8 out of 10. Its great for someone who needs a filtered reusable bottle, and doesn’t care too much about the colors or design. The filter is great in durability and really tastes refreshing. If you do however, want a bottle that has more customization features, I would suggest you check out the bobble, which we will be doing a review on soon.

How to Clean a Brita Water Bottle

As part of the Natural Living Series I have teamed up with BRITA water to do a review of the Marella jug and Fill & Go travel filter. In this post I will cover the Fill & Go as I also have a BRITA Fill & Go travel filter in pink to giveaway!

Now, I am not new to water filters, I think most people have them right? BUT do you actually use them? I know I go through phases of using mine, then I run out of filters or get lazy to keep refilling them. Well, I am NOT going to be lazy any more. After doing this review and really thinking about the quality of water I put inside me, and more importantly in Thomas. I am fully committed to drinking better quality water. This handy bottle has the filter built inside the lid so I can drink water on the go, anytime, anywhere.

As I pointed out in my post about my Top Tips for Drinking More Water, tap water quality isn’t the greatest. It contains chemicals and pesticides such as Chlorine, Fluorosilicic acid, Aluminium sulphate, Calcium hydroxide, Sodium silico and even Estrogen hormones. Going through old pipes can also lead to bacteria and lead contamination. Why wouldn’t you filter it? Bottled mineral water can get expensive, and all the wasted plastic isn’t good for the environment. I love the idea of the Fill & Go being better for the environment as it’s a reusable bottle which helps reduce the amount of plastic bottles thrown away everyday.

The BRITA Fill&Go is very stylish. I love the sleek look of the bottle- it’s got to be one of the best looking bottles on the market. It’s available in lots of colours too!

How to Clean a Brita Water Bottle

You have to insert a BRITA Fill&Go filter Disc once a week and there are 4 filter discs included with the Fill&Go bottle. Here’s the filter-

How to Clean a Brita Water Bottle

The filter significantly reduces chlorine, other taste impairing substances and fine solids. Now, I guess the amount of times you change the filter would depend on the usage (it says one filter disc can filter up to 20 litres of water). I use mine everyday as I take it with me whenever I go out or go to the gym. I also take it to bed with me- I need a whole 0.6L bottle of water at least with all the breastfeeding. So I would need to change mine every week.

The Fill & Go definitely makes the water taste better, the water also seems easier to swallow. I guess this is because a lot of the chlorine and other chemicals have been reduced. It’s easy to drink from and Thomas loves drinking from it. This is always a plus as it’s so difficult to get him to drink water these days! I think it’s the shape of the bottle and the fact that it’s new, he just loves it. It’s BPA free too so there are no worries with young children using it. My husband also loves it, we have the grey one and so it’s great for men to use too.

How to Clean a Brita Water Bottle

It’s easy to clean, dishwasher safe and the filter takes 2 seconds to insert. It has an optional straw with the bottle so you can either sip the water using the straw, or take the straw out and tilt the bottle to get the water (I must say I find it easier not to use the straw and just tip it up).

How to Clean a Brita Water Bottle

Would you like a BRITA Fill & Go in pink?
How to Clean a Brita Water Bottle
I have one to giveaway to a subscriber. So fill out the form below for your change to win!

Open to those 16 and above.
Ends 1am 5th January 2015
Entries will be added to the Happyhealthymumma monthly newsletter
UK postage only.
Only available in pink, I have the filter and will post out to you within 3 days of the giveaway ending.